SAE-AS-85049B-2007.pdf
《SAE-AS-85049B-2007.pdf》由会员分享,可在线阅读,更多相关《SAE-AS-85049B-2007.pdf(65页珍藏版)》请在三一文库上搜索。
1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there
2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2007 SAE International All rights reserved. No part of this publication m
3、ay be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA)
4、 Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org AS85049 REV. B AEROSPACE STANDARD Issued 1998-08 Revised 2007-03 Superseding AS85049A (R) Connector Accessories, Electrical General Specification For FSC 5935 RATIONALE Revised to include comments received by the gov
5、ernment and industry. Removed government jargon and updated specification references. WARNING This document includes cadmium as a plating material. The use of cadmium has been restricted and/or banned for use in many countries due to environmental and health concerns. The user should consult with lo
6、cal officials on applicable health and environmental regulations regarding its use. 1. SCOPE 1.1 Scope This specification covers connector accessories for use with electrical connectors under environmental or non- environmental conditions. Applicable connector accessories defined in this specificati
7、on are delineated for the suppression of Electromagnetic Interference (EMI) and Radio Frequency Interference (RFI). 1.1.1 Connector Accessory Categories Connector accessories covered in this specification shall include but are not limited to the following categories: Category Item Description 1A Hea
8、vy Duty 1B Medium Duty Connector Accessory, Cable Sealing, Environmental Connector Accessory, Cable Sealing, Environmental Provides waterproofing and environmental sealing under specific hydrostatic pressure. Straight, 90, or 45 configurations. May include termination features for individual or over
9、all EMI/RFI shielding. May include strain relief. Withstands most severe shock, vibration, cable pullout, and external bending moment. Same as Category 1A. Withstands less severe shock, vibration, cable pullout, and external bending moment than Category 1A. Copyright SAE International Provided by IH
10、S under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:31:36 MSTNo reproduction or networking permitted without license from IHS -,-,- SAE AS85049 Revision B - 2 - Category Item Description 1C Light Duty Connector Accessory, Cable Sealing, Environmental Same as
11、for Category 1A. Withstands less severe shock, vibration, and external bending moment than Category 1B. No cable pullout capability. 2A Heavy Duty 2B Medium Duty 2C Light Duty Connector Accessory, Environmental Connector Accessory, Environmental Connector Accessory, Environmental Does not provide wa
12、terproofing and environmental sealing under hydrostatic pressure. Straight, 90, or 45 configurations. May include termination features for individual or overall EMI/RFI shielding. May include strain relief. Withstands most severe shock, vibration, cable pullout, and external bending moment. Same as
13、Category 2A. Withstands less severe shock, vibration, cable pullout, and external bending moment than Category 2A. Same as Category 2A. Withstands less severe shock, vibration, and external bending moment than Category 2B. No cable pullout capability. 3A Heavy Duty 3B Medium Duty Connector Accessory
14、, Nonenvironmental Connector Accessory, Nonenvironmental May provide termination features for individual or overall, wire or cable, shielding. May extend working area for wire or cable termination. Straight, 90 or 45 configurations. May include termination features for individual or overall EMI/RFI
15、shielding. May include strain relief. Withstands most severe shock, vibration, cable pullout, and external bending moment. Same as Category 3A. Withstands less severe shock, vibration, cable pullout, and external bending moment than Category 3A. 3C Light Duty Connector Accessory, Nonenvironmental Sa
16、me as Category 3A. Withstands less severe shock, vibration, and external bending moment than Category 2B. No cable pullout capability. Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:31:36 MSTNo reproduction or ne
17、tworking permitted without license from IHS -,-,- SAE AS85049 Revision B - 3 - Category Item Description 4A Heavy Duty 4B Medium Duty 4C Light Duty Connector Accessory, Strain Relief, Nonenvironmental Connector Accessory, Strain Relief, Nonenvironmental Connector Accessory, Strain Relief, Nonenviron
18、mental Provides mechanical strain and side loading relief to wire bundles and cable support to jacketed cables. Straight, 90, or 45 configurations. May be attached to wire bundle or cable by means of metal clamp, plastic straps, lacing cord, or twine. Withstands same shock, vibration, cable pullout,
19、 and external bending moment as medium duty connector accessories of Categories 1, 2, and 3. Same as Category 4A. Withstands less severe shock, vibration, cable pullout, and external bending moment than Category 4A. Same as Category 4A. Withstands less severe shock, vibration, cable pullout, and ext
20、ernal bending moment than Category 4B. 5 Connector Accessory, Adapter, Shrink Boot and Ring, Potting Boot Provides means of attaching heat shrinkable boot to connector. 7 Connector Accessory, Miscellaneous Devices Examination of product. This category defines connector accessories which require rela
21、tively few test procedures for qualification. Additional requirements and test procedures shall be defined in the individual specification sheets. 8A 8B Connector Accessory, Adapter, Conduit, Cable Sealing Connector Accessory, Adapter, Conduit, Nonenvironmental Provides waterproofing and environment
22、al sealing under hydrostatic pressure. Straight and angled configurations. Provides termination area for connector conduit. Straight or angled configurations. 9 Connector Accessory, Miscellaneous Components Examination of product. This category defines connector accessory components which do not req
23、uire qualification. The manufacturer is required to maintain examination of product records as evidence of compliance on the first lot of each size produced. These records shall be made available to the user upon request. 1.2 Classification Connector accessories shall be of the size, style, finish,
24、and class as specified on the applicable military specification sheet (see 3.1). Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 18:31:36 MSTNo reproduction or networking permitted without license from IHS -,-,- SAE
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAE AS 85049 2007
链接地址:https://www.31doc.com/p-3793601.html