SAE-J1362-2007.pdf
《SAE-J1362-2007.pdf》由会员分享,可在线阅读,更多相关《SAE-J1362-2007.pdf(129页珍藏版)》请在三一文库上搜索。
1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there
2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2007 SAE International All rights reserved. No part of this publication m
3、ay be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA)
4、 Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org J1362 REV. JAN2007 SURFACE VEHICLE RECOMMENDED PRACTICE Issued 1986-08 Revised 2007-01 Superseding J1362 DEC2003 Graphical Symbols for Operator Controls and Displays on Off-Road Self-Propelled Work Machines RATIONALE
5、 This revision of SAE J1362 corrects some errors in the December 2003 published edition, adds a number of new symbols, clarifies language related to sizing of symbols in actual usage, and adds a new clause about adaptation of symbols as digital display icons. FOREWORD SAE J1362 presents graphical sy
6、mbols for use on operator controls and other displays on off-road work machines as defined in SAE J1116 plus mobile cranes. Symbols for agricultural equipment other than the basic agricultural tractor are covered by ASAE S304 and are therefore excluded from the scope of SAE J1362 of these symbols ha
7、ve been approved for DIS ballot by one or more ISO technical committees. TABLE OF CONTENTS 1. SCOPE2 2. REFERENCES2 2.1 Applicable Publications.2 2.1.1 SAE Publication 2 2.1.2 ISO Publications3 2.1.3 Other Publications.3 3. DEFINITIONS .3 3.1 Symbol 3 4. GENERAL.3 5. COLOR .4 6. ADAPTATION OF SYMBOL
8、S AS DIGITAL DISPLAY ICONS.5 7. DEVELOPMENT OF NEW SYMBOLS.5 8. BASE SYMBOLS5 9. GENERAL SYMBOLS.7 10. ENGINE SYMBOLS15 11. TRANSMISSION SYMBOLS 21 12. HYDRAULIC SYSTEM SYMBOLS.25 13. BRAKE SYSTEM SYMBOLS27 14. FUEL SYSTEM SYMBOLS.29 15. LIGHTING SYMBOLS.31 16. WINDOW/VISIBILITY SYMBOLS.34 17. CLIMA
9、TE CONTROL SYMBOLS .37 18. SEAT SYMBOLS 39 19. TIRE, WHEEL AND AXLE SYMBOLS42 SAE J1362 Revised JAN2007 - 2 - 20. STEERING SYMBOLS .44 21. AGRICULTURAL TRACTOR SYMBOLS.46 22. INDUSTRIAL TRACTOR SYMBOLS51 23. STABILIZER SYMBOLS.52 24. OUTRIGGER SYMBOLS54 25. CLAMSHELL BUCKET SYMBOLS.56 26. EARTHMOVIN
10、G GRAPPLE SYMBOLS.57 27. DOZER SYMBOLS.58 28. GRADER SYMBOLS 60 29. SCRAPER SYMBOLS 63 30. EXCAVATOR / BACKHOE SYMBOLS.66 31. EXCAVATOR / SHOVEL SYMBOLS70 32. LOADER SYMBOLS.71 33. RIPPER OR SCARIFIER SYMBOLS75 34. TREE HARVESTER / FELLER BUNCHER SYMBOLS .77 35. DELIMBER SYMBOLS .79 36. FELLING EQUI
11、PMENT SYMBOLS81 37. BUNK JAWS / GRAB ARMS SYMBOLS83 38. LOG HANDLING EQUIPMENT SYMBOLS85 39. TOPPING KNIFE SYMBOLS89 40. FORESTRY SAW SYMBOLS.90 41. GRAPPLE SKIDDER SYMBOLS91 42. LOG LOADER SYMBOLS 93 43. LOADGATE SYMBOLS95 44. WINCH SYMBOLS96 45. TELESCOPING JIB (BOOM) CRANE SYMBOLS97 46. FIXED LEN
12、GTH JIB (BOOM) CRANE SYMBOLS.99 47. DUMPER / HAULER SYMBOLS 101 48. TRENCHER SYMBOLS102 49. HORIZONTAL DIRECTIONAL DRILLING MACHINE SYMBOLS109 50. SWEEPER SYMBOLS116 51. ROAD-BUILDING EQUIPMENT SYMBOLS 123 52. COUNTERWEIGHT SYMBOLS .125 53. WORK PLATFORM SYMBOLS126 54. NOTES126 54.1 Marginal Indicia
13、.126 APPENDIX A - GUIDELINES FOR DEVELOPMENT AND EVALUATION OF GRAPHICAL SYMBOLS .127 1. SCOPE SAE J1362 presents graphical symbols for use on operator controls and other displays on off-road work machines as defined in SAE J1116 plus mobile cranes. Symbols for agricultural equipment other than the
14、basic agricultural tractor are covered by ASAE S304 and are therefore excluded from the scope of SAE J1362. 2. REFERENCES 2.1 Applicable Publications The following publications form a part of this specification to the extent specified herein. The latest issue of SAE publications shall apply. 2.1.1 S
15、AE Publication Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org. SAE J1116 Categories of Off-Road, Self-Propelled Work Machines SAE J1362 Revised JAN2007 - 3 - 2.1.2 ISO Publications Available
16、from ANSI, 25 West 43rd Street, New York, NY 10036-8002, Tel: 212-642-4900, www.ansi.org. ISO 3767-1 Tractors, machinery for agriculture and forestry, powered lawn and garden equipmentSymbols for operator controls and other displaysPart 1: Common symbols ISO 3767-2 Tractors, machinery for agricultur
17、e and forestry, powered lawn and garden equipmentSymbols for operator controls and other displaysPart 2: Symbols for agricultural tractors and machinery ISO 3767-4 Tractors, machinery for agriculture and forestry, powered lawn and garden equipmentSymbols for operator controls and other displaysPart
18、4: Symbols for specialized forestry machinery ISO 6405-1 Earth-moving machinerySymbols for operator controls and other displaysPart 1: Common symbols ISO 6405-2 Earth-moving machinerySymbols for operator controls and other displaysPart 2: Specific symbols for machines, equipment, and accessories ISO
19、 7000 Graphical symbols for use on equipmentIndex and synopsis ISO 7296-2 CranesGraphical symbolsPart 2: Symbols for mobile cranes ISO 80416-2 Basic principles for graphical symbols for use on equipmentPart 2: Form and use of arrows ISO 80416-4 Basic principles for graphical symbols for use on equip
20、mentPart 4: Guidelines for the adaptation of graphical symbols for use on screens and displays (icons) 2.1.3 Other Publications ASAE S304 Graphical symbols for operator controls and displays on agricultural equipment IEC 60417 Graphical symbols for use on equipment IEC 80416-1 Basic principles for g
21、raphical symbols for use on equipmentPart 1: Creation of symbol originals IEC 80416-3 Basic principles for graphical symbols for use on equipmentPart 3: Guidelines for the application of graphical symbols 3. DEFINITIONS For the purpose of SAE J1362, the following definition from ISO 80416-1 applies:
22、 3.1 Symbol A visually perceptible figure used to transmit information independent of language. It may be produced by drawing, printing, or other means. 4. GENERAL 4.1 Use symbols as shown in SAE J1362. However, symbols which are shown in outline form may be filled in actual use for enhanced clarity
23、 of reproduction and improved visual perception by the operator, unless otherwise noted for individual symbols. Refer to IEC 80416-3. 4.2 Limitations inherent in some reproduction and display technologies may require increased line thickness or other minor modifications of symbols. Such modification
24、s are acceptable provided the symbol is unchanged in its basic graphical elements and remains easily discernible by the operator. SAE J1362 Revised JAN2007 - 4 - 4.3 Additionally, to improve the appearance and perceptibility of a graphical symbol, or to coordinate with the design of the equipment to
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAE J1362 2007
链接地址:https://www.31doc.com/p-3793608.html