SAE-AS-85049-32A-2007.pdf
《SAE-AS-85049-32A-2007.pdf》由会员分享,可在线阅读,更多相关《SAE-AS-85049-32A-2007.pdf(4页珍藏版)》请在三一文库上搜索。
1、 AEROSPACE STANDARD (R) CONNECTOR ACCESSORIES, ELECTRICAL, BACKSHELL, NONENVIRONMENTAL, 90, SHIELDED TERMINATION, CATEGORY 7 (FOR MIL-DTL-38999 SERIES I AND II CONNECTORS) AS85049/32 Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retr
2、ieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: Customer
3、Servicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2000-05 REVISED 2007-03 THIRD ANGLE PROJECTION CUSTODIAN: SAE AE-8/AE-8C1 REV. A FEDERAL SUPPLY CLASS 5935 AS85049/32 SHEET 1 OF 4 REV. A SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state o
4、f technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years
5、at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. RATIONALE REVISED TO INCLUDE COMMENTS RECEIVED BY THE GOVERNMENT AND INDUSTRY USERS. UPDATED ALL REFERENCE SPECIFICATIONS. REMOVED GOVERNMENT JARGON AS A RESULT OF THE WORD-FOR-WORD CONVERSI
6、ON. THE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE LATEST ISSUE OF: SAE AS85049. ADAPTERABCL INCHESmm SHELLDIADIADIA 900.0942.39 SIZESERIES II SERIES IMAXMAXMAXMAX0.3599.12 8 8 90.5940.3590.6560.7190.40610.31 1010110.7190.4060.7810.7660.
7、50012.70 1212130.8440.5000.9380.8590.57814.68 1414150.9690.5781.0620.9380.59415.09 1616171.0940.6411.2191.0000.64116.28 1818191.2190.6881.3441.0470.65616.66 2020211.3440.7341.4691.0940.68817.48 2222231.4690.7961.5941.1560.71918.26 2424251.5940.8591.7191.2190.73418.64 0.76619.46 0.78119.84 0.79620.22
8、 0.84421.44 3. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION0.85921.82 ONLY.0.93823.83 1.00025.40 1.04726.59 1.06226.97 1.09427.79 1.15629.36 1.21930.96 1.34434.14 1.46937.31 1.59440.49 1.71943.66FIGURE 1 - DIMENSIONS AND CONFIGURATION - 90 ADAPTER NOTES: 1. DIMENSIONS ARE IN INCHES. 2. DIMEN
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAE AS 85049 32 2007
链接地址:https://www.31doc.com/p-3793641.html