SAE-J1508-2009.pdf
《SAE-J1508-2009.pdf》由会员分享,可在线阅读,更多相关《SAE-J1508-2009.pdf(79页珍藏版)》请在三一文库上搜索。
1、_ SAE Technical Standards Board Rules provide that: “ This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising ther
2、efrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2009 SAE International All rights reserved. No part of this publication
3、may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA
4、) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SURFACE VEHICLE STANDARD J1508 MAR2009 Issued 1987-06 Revised 2009-03 Superseding J1508 AUG1997 Hose Clamp Specifications RATIONALE This document is being updated to current requirements to meet manufacturing practi
5、ces and application needs. TABLE OF CONTENTS 1. SCOPE 3 1.1 Purpose . 3 2. REFERENCES 3 2.1 Applicable Publications . 3 2.2 Related Publications . 4 3. DEFINITIONS . 5 3.1 Free Torque 5 3.2 Durability Torque . 5 3.3 Installation Torque . 5 3.4 Ultimate Torque . 5 4. CLASSIFICATION . 5 4.1 Group #1 (
6、Types “ A,” “ AHH,” “ B,” “ D,” “ C,” “ F,” “ FEO,” “ FE,” “ HD,” “ I,” “ M,” “ MX,” “ TB,” “ SSC,” and “ G” . 5 4.2 Group #2 (Types “ E,” “ CTB,” or “ CTW” ) 30 4.3 Group #3 (Types “ SLA,” “ SLF,” “ SLTF,” “ SLHD,” “ T,” “ SLTB,” “ SSPC,” and “ SLFEO” . 30 4.4 Group #4, (Types “ J,” “ OES,” “ TE,”
7、“ SEC” ) . 54 4.5 Group #5 (Type “ LP” ) 59 4.6 Group #6 (Type “ H” ) 60 5. GENERAL REQUIREMENTS . 61 5.1 Group #1 . 61 5.2 Group #2 . 61 5.3 Group #3 . 62 5.4 Group #4 . 62 5.5 Group #5 . 62 5.6 Group #6 . 62 6. MATERIALS 62 6.1 MaterialsGroup #1 . 62 6.2 MaterialsGroup #2 . 65 6.3 MaterialsGroup #
8、3 . 65 6.4 MaterialsGroup #4 . 67 SAE J1508 Revised MAR2009 Page 2 of 79 6.5 MaterialGroup #5 . 67 6.6 MaterialsGroup #6 . 67 7. FINISHES 67 7.1 FinishesGroup #1 67 7.2 FinishesGroup #2 68 7.3 FinishesGroup #3 69 7.4 FinishesGroup #4 70 7.5 FinishesGroup #5 70 7.6 FinishGroup #6 70 8. THREADS . 70 8
9、.1 Types “ A,” “ AHH,” “ B,” “ C,” “ D,” “ G,” and “ SLA” 70 8.2 Types “ F,” “ FEO,” “ HD,” “ I,” “ M,” “ MX,” “ SLF,” “ SLTF,” “ SLFEO,” “ SLHD,” and “ T” 70 8.3 Types “ TB” and “ SLTB” . 70 8.4 Types “ SSC” and “ SSPC” . 70 9. SCREWS 71 9.1 Types “ A,” “ AHH,” and “ SLA” 71 9.2 Type “ B” 71 9.3 Ty
10、pe “ C” 71 9.4 Type “ D” 71 9.5 Types “ F,” “ HD,” “ I,” “ M,” “ MX,” “ SLF,” “ SLTF,” SLFEO,” “ SLHD,” and “ T” . 71 9.6 Types “ FEO” and “ FE” . 71 9.7 Types “ TB” and “ SLTB” . 71 9.8 Types “ SSPC” and “ SSC” . 71 10. NUTS. 71 10.1 Types “ A,” “ SLA,” “ B,” “ C,” “ G,” and “ D” 71 10.2 Type “ TB”
11、 71 10.3 Type “ SLTB” 71 10.4 Types “ SSPC” and “ SSC” . 72 11. IDENTIFICATION 72 11.1 Types “ A,” “ AHH,” and “ SLA” 72 11.2 Types “ B” and “ C” 72 11.3 Type “ E” 72 11.4 Types “ F,” “ FE,” “ FEO,” “ HD,” “ I,” “ M,” “ MX,” “ SLF,” “ SLFEO,” “ SLHD,” “ SLTF,” “ T,” “ TB,” and “ SLTB” . 72 11.5 Type
12、 “ CTB” 72 11.6 Type “ CTW” . 72 11.7 Type “ G” 72 11.8 Type “ J,” “ OES,” “ TE,” “ SEC,” “ SSPC,” and “ SSC” . 72 12. MANUFACTURERS NOTES . 72 12.1 Type “ B” Clamps. 72 12.2 Type “ CTW” . 73 13. CLAMP PERFORMANCE, ACCEPTANCE REQUIREMENTS, AND APPLICATION NOTES 73 13.1 Types “ A,” “ AHH,” and “ SLA”
13、 73 13.2 Type “ E” Clamps . 74 13.3 Types “ F,” “ FE,” “ FEO,” “ HD,” “ I,” “ M,” “ MX,” “ SLF,” “ SLFEO,” “ SLHD,” “ SLTF,” and “ T” Clamps 75 13.4 Type “ CTB” 76 13.5 Type “ CTW” . 76 13.6 Type “ TB” 77 13.7 Type “ SLTB” 78 13.8 Types “ J,” “ OES,” “ TE,” and “ SEC” . 78 -,-,- SAE J1508 Revised MA
14、R2009 Page 3 of 79 13.9 Types “ SSPC” and “ SSC” . 78 13.10 Type “ G” 78 14. NOTES 79 14.1 Marginal Indicia . 79 1. SCOPE This SAE Standard covers thirty-two (32) types of clamps most commonly and suitably being used on OEM coolant, fuel, oil, vacuum, and emission systems. 1.1 Purpose This document
15、is compiled for the specific purpose of describing the basic characteristics and minimum performance requirements recommended by the manufacturers. No application recommendations are intended or implied. For the benefit of the user in selecting appropriate products for their application, the committ
16、ee has published ancillary documents that may assist you in this selection. The documents are SAE J1610, SAE J1697, and TMC RP 332. 2. REFERENCES 2.1 Applicable Publications The following publications form a part of this specification to the extent specified herein. Unless otherwise indicated, the l
17、atest issue of SAE publications shall apply. 2.1.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org. SAE J178 Music Steel Wire and Springs SAE J402 New Steel Desi
18、gnation System for Wrought or Rolled Steel SAE J478 Slotted and Recessed Head Screws SAE J1086 Numbering Metals and Alloys SAE J1610 Test Method for Evaluating the Sealing Capability of Hose Connections with a PVT Test Facility SAE J1697 Recommended Practices for Design and Evaluation of Passenger a
19、nd Light Truck Coolant Hose Clamped Joints 2.1.2 ANSI and IFI Publications Available from ANSI, 25 West 43rd Street, New York, NY 10036-8002, Tel: 212-642-4900, www.ansi.org. ANSI B1.1, 3M Unified Inch Screw Thread ANSI B1.3M Screw Thread Gauging Systems for Dimensional Acceptability IFI 112 High Pe
20、rformance Thread Rolling Screws SAE J1508 Revised MAR2009 Page 4 of 79 2.1.3 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org. ASTM A 228 Standard Specification for Steel Wire, Music Spring Qu
21、ality ASTM A 525 Specification for General Requirements for Steel Sheet, Zinc-Coated (Galvanized) by the Hot-Dip Process ASTM B 117 Standard Method of Salt Spray (Fog) Testing 2.1.4 Military Publications Available from the Document Automation and Production Service (DAPS), Building 4/D, 700 Robbins
22、Avenue, Philadelphia, PA 19111-5094, Tel: 215-697-6257, http:/assist.daps.dla.mil/quicksearch/. MIL STD MS21044 Nut, Self-Locking, Hexagon, Regular Height, 250 F, 125 ksi Ftu and 60 ksi Ftu MIL STD MS21045 Nut, Self-Locking, Hexagon, Regular Height, 450 F, 125 ksi Ftu MIL STD MS39326 Clamp, Spring:
23、Hose (Low Pressure) Type “ E” 2.1.5 AISI Publication Available from American Iron and Steel Institute, 1140 Connecticut Ave., NW, Suite 705, Washington, DC 20036, Tel: 202-452-7100, www.steel.org. If specifications referred to in this document are no longer available through AISI, cross reference th
24、em to the SAE “ J” standards in 2.2.1. AISI Material Standards 2.1.6 TMC Publications Available from the Technology and Maintenance Council, American Trucking Associations, 2200 Mill Road, Alexandria, VA 22314, Tel: (703) 838-1700, . TMC RP 332 Guidelines for Hose, Clamps, and Fittings for Cooling a
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAE J1508 2009
链接地址:https://www.31doc.com/p-3793643.html