SAE-AS-9592B-2007.pdf
《SAE-AS-9592B-2007.pdf》由会员分享,可在线阅读,更多相关《SAE-AS-9592B-2007.pdf(4页珍藏版)》请在三一文库上搜索。
1、 AEROSPACE STANDARD BRACKET, ANGLE, 90, CRES UNS S32100, .190 BOLT AS9592 Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or
2、 otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1998-02 REVISED 2007-07 THIRD ANGLE PROJECTION CUSTO
3、DIAN: SAE E-25 REV. B FEDERAL SUPPLY CLASS 5340 AS9592 SHEET 1 OF 4 REV. B PROCUREMENT SPECIFICATION: NONE SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and
4、its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comm
5、ents and suggestions. RATIONALE CORRECT TYPOS FOR TWO PART NUMBERS IN TABLE 1 FOR BRACKETS 1.438 X .688, AND 1.438 X 1.000. NOTICE THE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9592A. THIS SAE STANDARD RETAINS THE SAME PART NUMBERS ESTABLISHED BY THE O
6、RIGINAL MILITARY DOCUMENT. ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCT LISTS (QPL) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATNG TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. FIGURE 1 - ANGLE BRACKET Copyright SAE Inte
7、rnational Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 21:35:06 MSTNo reproduction or networking permitted without license from IHS -,-,- AEROSPACE STANDARD BRACKET, ANGLE, 90, CRES UNS S32100, .190 BOLT AS9592 REV. B AS9592 SHEET 2 OF 4 REV
8、. B TABLE 1 - PART NUMBERS AND DIMENSIONS A - LENGTH .428 - .448 .490 - .510 .552 - .572 .615 - .635 B LENGTH PART NUMBER PART NUMBER PART NUMBER PART NUMBER .428 - .448 .490 - .510 .552 - .572 .615 - .635 .678 - .698 .740 - .760 .802 - .822 .865 - .885 .928 - .948 .990 - 1.010 1.052 - 1.072 1.115 -
9、 1.135 1.178 - 1.198 1.240 - 1.260 1.302 - 1.322 1.365 - 1.385 1.428 - 1.448 1.490 - 1.510 1.552 - 1.572 1.615 - 1.635 1.678 - 1.698 1.740 - 1.760 1.865 - 1.885 *MS9592-005 *MS9592-006 *MS9592-007 *MS9592-008 *MS9592-009 *MS9592-010 MS9592-011 *MS9592-012 MS9592-013 *MS9592-014 MS9592-015 *MS9592-01
10、6 MS9592-017 *MS9592-018 MS9592-019 *MS9592-020 MS9592-021 *MS9592-022 MS9592-023 *MS9592-024 MS9592-025 *MS9592-026 *MS9592-027 *MS9592-046 *MS9592-047 *MS9592-048 *MS9592-049 *MS9592-050 MS9592-051 *MS9592-052 MS9592-053 *MS9592-054 MS9592-055 *MS9592-056 MS9592-057 *MS9592-058 MS9592-059 *MS9592-
11、060 MS9592-061 *MS9592-062 MS9592-063 *MS9592-064 MS9592-065 *MS9592-066 *MS9592-067 *MS9592-087 *MS9592-088 *MS9592-089 *MS9592-090 MS9592-091 *MS9592-092 MS9592-093 *MS9592-094 MS9592-095 *MS9592-096 MS9592-097 *MS9592-098 MS9592-099 *MS9592-100 MS9592-101 *MS9592-102 MS9592-103 *MS9592-104 MS9592
12、-105 *MS9592-106 *MS9592-107 *MS9592-128 *MS9592-129 *MS9592-130 MS9592-131 *MS9592-132 MS9592-133 *MS9592-134 MS9592-135 *MS9592-136 MS9592-137 *MS9592-138 MS9592-139 *MS9592-140 MS9592-141 *MS9592-142 *MS9592-143 MS9592-144 *MS9592-145 MS9592-146 *MS9592-147 *PREFERRED SIZES. Copyright SAE Interna
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAE AS 9592 2007
链接地址:https://www.31doc.com/p-3793690.html