SAE-J463-2002.pdf
《SAE-J463-2002.pdf》由会员分享,可在线阅读,更多相关《SAE-J463-2002.pdf(42页珍藏版)》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2002 Society of Automotive Engineers, Inc. All rights reserved. No part of
3、this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER:Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4
4、970 (outside USA) Fax: 724-776-0790 Email: custsvcsae.org SAE WEB ADDRESS:http:/www.sae.org SURFACE VEHICLE STANDARD J463 ED. CHG. DEC2002 Issued1911-06 Editorial Change 2002-12 Superseding J463 SEP1981 Wrought copper and Copper Alloys 1.ScopeThis standard1 describes the chemical, mechanical, and di
5、mensional requirements for a wide range of wrought copper and copper alloys used in the automotive and related industries. 1.1Wrought forms covered by this standard include sheet, strip, bar, plate, rod, wire, tube, and shapes; however, form required must be specified by purchaser. 2.References 2.1A
6、pplicable PublicationsThe following publications form a part of this specification to the extent specified herein. 2.1.1ASTM PUBLICATIONSAvailable from ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. ASTM B248Specification for General Requirements for Wrought Copper and Copper-Alloy P
7、late, Sheet, Strip, and Rolled Bar ASTM B249Specificaiton for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, and Shapes ASTM B250Specification for General Requirements for Wrought Copper-Alloy Wire ASTM B251Specification for General Requirements for Wrought Copper-Alloy Wire 3.Ch
8、emical and Mechanical PropertiesThe chemical composition of products identified by the UNS designations shall conform to the limits shown in Table 1. Mechanical properties shall conform to limits shown in Table 2A (metric(si) units) or 2B (customary units). 3.1Products shall be of uniform quality an
9、d free from defects (such as desegregation, pipes, nonmetallic inclusions, cracks, seams, laps, buckles, and die or roll marks) detrimental to their appearance, fabrication and/or performance in service. 3.2Both inside and outside surfaces of tubing shall be clean and smooth. 1.If none of the alloys
10、 listed herein include the characteristics required for a particular application, users are encouraged to consider alloy spec- ifications listed in CDA Publication “Standards Handbook for Copper Alloy Wrought Mill Products,” published by the Copper Development Association, 405 Lexington Avenue, New
11、York, NY 10017, before creating specifications of their own. SAE 463 EditorialChange DEC2002 -2- 3.3Forgings shall not be brazed, soldered, welded, or ground to hide defects or to salvage defective products, unles specifically approved by the purchaser. 3.4Necessary brazes in soft annealed copper wi
12、re shall be in accordance with best commercial practice. 4.TestingUnless otherwise specified all properties stated herein are based on latest methods of test published in the ASTM Standards. 5.Dimensional TolerancesStandard forms of products identified by the UNS designations shall conform to the di
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAE J463 2002
链接地址:https://www.31doc.com/p-3793861.html