SAE-J444-2001.pdf
《SAE-J444-2001.pdf》由会员分享,可在线阅读,更多相关《SAE-J444-2001.pdf(6页珍藏版)》请在三一文库上搜索。
1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr
2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. QUESTIONS REGARDING THIS DOCUMENT: (412) 772-8512 FAX: (412) 776-0243 TO PLACE A DOCU
3、MENT ORDER; (412) 776-4970 FAX: (412) 776-0790 SAE WEB ADDRESS http:/www.sae.org Copyright 1993 Society of Automotive Engineers, Inc. All rights reserved.Printed in U.S.A. SURFACE VEHICLE 400 Commonwealth Drive, Warrendale, PA 15096-0001 RECOMMENDED PRACTICE An American National Standard J444 REV. M
4、AY93 Issued1946-01 Revised1993-05 Superseding J444 AUG84 (R) CAST SHOT AND GRIT SIZE SPECIFICATIONS FOR PEENING AND CLEANING 1.ScopeThis SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds w
5、ith the opening of the nominal test sieve, in ten thousandths of inches1, preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E 11. The accompanying shot and grit classifications an
6、d size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users. 2.References 2.1Applicable PublicationThe following publication forms a part of this specification to the extent specified herein. 2.1.1ASTM PUBLICATIONAvailable from AST
7、M, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. ASTM E 11Standard Specifications for Wire Cloth Sieves for Testing Purposes 2.2Related PublicationsThe following publications are provided for information purposes only and are not a required part of this document. The latest issue of SAE p
8、ublications shall apply. 2.2.1SAE PUBLICATIONSAvailable from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001. SAE J445Metallic Shot and Grit Mechanical TestingFor Information on Shot Durability Determination SAE J827Cast Steel ShotFor Information on Composition and Shapes SAE J1993Cast Steel
9、GritFor Information on Composition and Shapes SAE J2175Low Carbon Steel ShotFor Information on Composition and Shapes 1.Example: S-550 indicates a cast steel shot identified by a nominal sieve opening of 0.0555 in. SAE J444 Revised MAY93 -2- 3.Testing ProcedureSieve Analysis 3.1Equipment 3.1.1A rota
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAE J444 2001
链接地址:https://www.31doc.com/p-3793866.html