TIA-455-176-A-2003.pdf
《TIA-455-176-A-2003.pdf》由会员分享,可在线阅读,更多相关《TIA-455-176-A-2003.pdf(38页珍藏版)》请在三一文库上搜索。
1、 TIA STANDARD ANSI/TIA-455-176-A-2003 Approved: May 21, 2003 FOTP-176 IEC-60793-1-20 Optical Fibres Part 1-20: Measurement Methods and Test Procedures Fibre Geometry TIA-455-176-A (Revision of TIA/EIA-455-176) MAY 2003 TELECOMMUNICATIONS INDUSTRY ASSOCIATION Representing the telecommunications indus
2、try in association with the Electronic Industries Alliance NOTICE TIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assistin
3、g the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Standards and Publications shall not in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and P
4、ublications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domestically or internationally. Standards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By suc
5、h action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. Further details of the development process are available in the TIA Engineering Manual, located at http:/www.tiaonline.org/standards/sfg/engine
6、ering_manual.cfm This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulator
7、y limitations before its use. These Materials are subject to copyright claims of IEC, ANSI, and TIA. No part of this publication may be reproduced in any form, including an electronic retrieval system, without the prior written permission of TIA. All requests pertaining to the FOTP-176 IEC-60793-1-2
8、0: Measurement Methods and Test Procedures Fibre Geometry Standard should be submitted to TIA. (From Standards Proposal No. 3-4310-RV1, formulated under the cognizance of the TIA FO-4.6 Subcommittee on Optical Fibers.) Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION 2003 Standards and Technolog
9、y Department 2500 Wilson Boulevard Arlington, VA 22201 U.S.A. PRICE: Please refer to current Catalog of TIA TELECOMMUNICATIONS INDUSTRY ASSOCIATION STANDARDS AND ENGINEERING PUBLICATIONS or call Global Engineering Documents, USA and Canada (1-800-854-7179) International (303-397-7956) or search onli
10、ne at http:/www.tiaonline.org/standards/search_n_order.cfm All rights reserved Printed in U.S.A. -,-,- NOTICE OF DISCLAIMER AND LIMITATION OF LIABILITY The document to which this Notice is affixed (the “Document”) has been prepared by one or more Engineering Committees or Formulating Groups of the T
11、elecommunications Industry Association (“TIA”). TIA is not the author of the Document contents, but publishes and claims copyright to the Document pursuant to licenses and permission granted by the authors of the contents. TIA Engineering Committees and Formulating Groups are expected to conduct the
12、ir affairs in accordance with the TIA Engineering Manual (“Manual”), the current and predecessor versions of which are available at http:/www.tiaonline.org/standards/sfg/engineering_manual.cfm. TIAs function is to administer the process, but not the content, of document preparation in accordance wit
13、h the Manual and, when appropriate, the policies and procedures of the American National Standards Institute (“ANSI”). TIA does not evaluate, test, verify or investigate the information, accuracy, soundness, or credibility of the contents of the Document. In publishing the Document, TIA disclaims an
14、y undertaking to perform any duty owed to or for anyone. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes no search or investigation for IPR. When
15、IPR consisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any obligation to investigate or inquire into, the
16、 scope or validity of any claims of IPR. TIA does not enforce or monitor compliance with the contents of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR
17、IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NON-INFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIM
18、S ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODU
19、CED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES F
20、OR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF TH
21、E USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. -,-,- PLEASE! DONT VIOLATE THE LAW! This document is copyrighted by the TIA and may not be reproduced without prior permission of the Telecommunications Industry Association. For information cons
22、ult our website at http:/www.tiaonline.org/about/faqDetail.cfm?id=18 Organizations may obtain permission to reproduce a limited number of copies through entering into a license agreement. For information, contact: Global Engineering Documents 15 Inverness Way East Englewood, CO 80112-5704 U.S.A. or
23、call U.S.A. and Canada 1-800-854-7179, International (303) 397-7956 -,-,- FOREWARD With the adoption of international standard IEC 60793-1-20 (Optical Fibres Part 1-20: Measurement Methods and Test Procedures Fibre Geometry) TIA-455-176-A supercedes the current TIA-455-176 (FOTP-176 Method for Measu
24、ring Optical Fiber Cross-Sectional Geometry by Automated Grey-Scale Analysis). It replaces the following documents: (FOTP-29 Refractive Index Profile, Transverse Interference Method) (FOTP-43 Output Near-field Radiation Pattern Measurement of Optical Waveguide Fibers) (FOTP-44 Refractive Index Profi
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- TIA 455 176 2003
链接地址:https://www.31doc.com/p-3800927.html