塑料制品质量问题英文描述要点.pdf
《塑料制品质量问题英文描述要点.pdf》由会员分享,可在线阅读,更多相关《塑料制品质量问题英文描述要点.pdf(17页珍藏版)》请在三一文库上搜索。
1、Surface Appearance外观 G 0 Surface Appearance 外观 Glossiness/gloss finish 光洁度 Matt finish/matt surface 毛面 Glass fiber rich surface/glass emergence on the surface 玻纤外露 Blooming/surface blooming 表面析出 White patches on surface 表面白斑 Silver marks/silver streak 银纹 Splay mark 水纹 Flow mark 流纹 Weld line 溶结纹 Brit
2、tle/brittleness 脆 Bubbles/trapped gas 气泡 Void 孔 Burn marks 烧伤 FR failed 阻燃不合格 Flame rating V-2 阻燃 V-2 Poor dispersion 分散不好 FR/PTFE agglomerates etc 阻燃剂 /PTFE 结块 Pellet porous 粒子不密 /蜜蜂窝 Low impact/tensile etc 物理性能低 High flow/filler content etc 流动性 /填充 过高 Longs/fines/doubles 长粒 /碎屑 /连粒 Poor cut 粒形不好 B
3、ristle/voids 表面有小气泡 /孔 Glass bundles 玻纤结团 Product was rejected due to 产品不能接受因为 High moisture level 高水分 Warpage/warped 翘曲 Shrinkage/shrink 收缩 Sink marks 缩影 Short shot/short molding 打不满 Distortion 变形 Over dimension 尺寸过大 Under dimension 尺寸过小 Flashing 飞边 Discoloration 变色 Off color颜色差异 Flow r 0 Off color
4、 颜色差异 Flow rate 流动率 Viscous 粘 High flow 高流动 Low flow 低流动 Sticky 粘 Mold release 脱模 Antioxidant 抗氧剂 Flame retardant agent 阻燃剂 Heat stabilizer 热稳定剂 Chopped glass fiber 短切玻纤 Roving glass fiber 粗纱 /长玻纤 Glass beads 玻璃微珠 Milled fiber 碾磨纤 Molybdenum disulfide/moly/MoS2 二硫化钼 Colorant 着色剂 Pigment 颜料 Dye 染料 Ac
5、cepted product specification 接受产品规格 Approved our product 认可我们的产品 Re-set spec 重新定标准 Add in extra 添加多一点 Reduced content 减少 含量 Dropped/reduced by x% 减少 含量 % Confirmed color standard 确认颜色标准 Approved color standard 认可颜色标准 Re-confirmed color standard 重新确认颜色标准 Qualified our product 认可我们的产品 Undergoing heat
6、aging test 在做热老化实验 Product is under testing 产品在测试当中 Received first order 接了第一个定单 Expected to finish by 预计在 完成 Expected order is xMT 预计定单量 吨 Estimated annual/monthly consumption 预计年 /月用量 外向型塑料制品企业常用的英语词汇一 来源:中国塑料产业链网我要评论: 0时间: 2009-7-6 一、组织机构及职位 XX 电子有限公司XX Electronics CO., Ltd 总经理办公室General manager
7、s office 企管部 Enterprise management department (EM) 行政部 Administration department (AD) 销售部 Sales department (SD) TodayHot 财务部 Financial department (FD) 技术部 Technology department (TD) 物控部 Production material control department (PMC) 生产部 Production department(PD) 模具部 Mold manufacturing department, Tool
8、ing manufacturing department (TM) 品管部 Quality Assurance department (QA) 冲压车间Stamp workshop, press workshop 注塑车间injection workshop 装配车间Assembly workshop 模具装配车间Mold and die Assembly workshop 金属加工车间metal machine workshop HotTag 电脉冲车间Electric discharge process workshop 线切割车间wire cutting process workshop
9、 工磨车间Grinding workshop 总经理 General manager (GM) 副总经理Vice-general manager 经理 manager 董事长 president 副董事长Vice-president XX 部门经理Manager of XX department 主任、主管supervisor 拉长 Line leader 组长 Foreman, forelady 秘书 secretary 文员 clerk 操作员 operator 助理 assistant 二、产品 连接器 connector 端子 terminal 条型连接器bar connector 阴
10、连接器Housing 阳连接器wafer 线束 wire harness 间距 space TodayHot 额定电压rated voltage 额定电流rated current 接触电阻 contact resistance 绝缘电阻insulation resistance 超声波焊接ultrasonic welding 耐压 withstand voltage 针 pin 物料编号 part number 导线 wire 基体金属Base metal 电缆夹 cable clamp 倒角 chamfer 接触面积 contact area 接触件安装孔contact cavity Ho
11、tTag 接触长度 contact length 接触件电镀层contact plating 接触压力 contact pressure 接触件中心距contact space 接触簧片 contact spring 插孔 socket contact 法兰、凸缘Flange 界面间隙interfacial gap 键 Key 键槽 keyway 过渡段 ramp 屏蔽套 shielding 定位基准 Datum reference 扁平电缆flat cable ,Ribbon cable 柔性印刷电线Flexible printed wiring 多层印制电路Multilayer print
12、ed circuit 焊盘 pad 图形 pattern 间距 pitch 负极 Negative pole 正极 positive pole 回流 Reflow 原理图 Schematic diagram 单面板 single sided board 双面板 Two-sided board,Double-sided board 表面安装 surface Mounting 翘曲 warp , bow 波峰焊 wave soldering 编织层 braid 同轴电缆 coaxial cable 电介质 dielectric 电缆中导线的头数ends 外部干扰external interfere
13、nce 填充物 filler 护套 jacket 比重 specific gravity 电阻的温度系数Temperature coefficient of resistance 三、模具 塑料模具 mould of plastics 注塑模具injection mould 冲压模具 die 模架 mould base 定模座板 Top clamping plate Top plate Fixed clamp plate 水口推板 stripper plate TodayHot A 板 A plate B 板 B plate 支承板support plate 方铁spacer plate 底针
14、板ejector plate 面针板ejector retainer plate 回针Return pin 导柱Guide pin 有托导套Shoulder Guide bush 直导套Straight Guide bush 动模座板Bottom clamp plate Moving clamp plate 基准线 datum line 基准面 datum plan HotTag 型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针 ejector pin 单腔模具 single cavity mould 多腔模具 multi-cavity
15、 mould 多浇口 multi-gating 浇口 gate 缺料 starving 排气 breathing 光泽 gloss 合模力 mould clamping force 锁模力 mould locking force 挤出 extrusion 开裂 crack 循环时间 cycle time 老化 aging 螺杆 screw 麻点 pit 嵌件 insert 活动镶件 movable insert 起垩 chalking 浇注系统feed system 主流道sprue 分流道 runner 浇口 gate 直浇口 direct gate , sprue gate 轮辐浇口 sp
16、oke gate , spider gate 点浇口 pin-point gate 测浇口 edge gate 潜伏浇口 submarine gate , tunnel gate 料穴 cold-slug well 浇口套 sprue bush 流道板 runner plate 排飞槽 vent 分型线(面) parting line 定模 stationary mould,Fixed mould 动模 movable mould, movable half 上模 upper mould, upper half 下模 lower mould, lower half 型腔 cavity 凹模 c
17、avity plate,cavity block 拼块 split 定位销 dowel 定位销孔 dowel hole 型芯 core 斜销 angle pin, finger cam 滑块 slide 滑块导板 slide guide strip 楔紧块 heel block, wedge lock 拉料杆 sprue puller 定位环 locating ring 冷却通 cooling channel 脱模斜度 draft 滑动型芯 slide core 螺纹型芯 threaded core 热流道模具hot-runner mould 绝热流道模insulated runner mou
18、ld 熔合纹 weld line (flow line) 三板式模具three plate mould 脱模 ejection 换模腔模具interchangeable cavity mould 脱模剂 release agent 注射能力 shot capacity 注射速率injection rate 注射压力injection pressure 差色剂 colorant 保压时间 holdup time 闭模时间 closing time 定型装置 sizing system 阴模 female mould,cavity block 阳模 male mould 电加工设备Electron
19、 Discharge Machining 数控加工中心CNC machine center 万能铁床Universal milling machine 卧式刨床Horizontal planer 车床 Engine lathe 平面磨床Surface grinding machine 去磁机 Demagnetization machine 万能摇臂钻床Universal radial movable driller 立式钻床 Vertical driller 超声波清洗机Ultrasonic clearing machine 四、品管 SPC statistic process control
20、 品管保证Quality Assurance 品管控制Quality control 来料检验IQC Incoming quality control TodayHot 巡检 IPQC In-process quality control 校对 calibration 动态试验 dynamic test 环境试验 Environmental test 非破坏性试验non-destructive test 光泽 gloss 击穿电压 (dielectric) breakdown voltage 拉伸强度 tensile strength 冷热骤变试验thermal shock test 环境试验
21、炉Environmental chamber 盐雾实验 salt spray test 绝缘电阻测试验仪Insulating resistance meter 内应力 internal stress 疲劳 fatigue HotTag 蠕变 creep 试样 specimen 撕裂强度 tear strength 缩痕 shrink mark, sink mark 耐久性 durability 抽样 sampling 样品数量 sample size AQL Acceptable Quality level 批量 lot size 抽样计划 sampling plan OC 曲线 operat
22、ion curve 试验顺序 sequence of tests 环境温度 ambient temperature 可焊性 solderability 阻燃性 flame resistance 五、生产 注塑机 injection machine 冲床 Punch machine 混料机 blender mixer 尼龙 nylon 黄铜brass 青铜bronze TodayHot 紫( 纯) 铜 copper 料斗 hopper 麻点 pit 配料 compounding 涂层 coating 飞边 flash 预热 preheating 再生料 reworked material 再生塑
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 塑料制品 质量问题 英文 描述 要点
链接地址:https://www.31doc.com/p-5207677.html