【优质文档】液压系统及液压缸外文翻译.pdf
《【优质文档】液压系统及液压缸外文翻译.pdf》由会员分享,可在线阅读,更多相关《【优质文档】液压系统及液压缸外文翻译.pdf(9页珍藏版)》请在三一文库上搜索。
1、液压传动 第十讲 制动器 力流体动力系统的优秀的特性之一是由电源产生,通过适当的控制和指导,并 通过电线传输,就可以轻松转换到几乎任何类型的机械运动所需要用到的地方。 使用一个合适的驱动装置,可以获得线性(直线)或者是旋转运动。驱动器是 一种转换流体动力机械力和运动的装置。缸、马达和涡轮机是最常见的将流体 动力系统应用于驱动设备的类型。这一章描述了各种类型的动作汽缸和他们的 应用程序、不同类型的流体汽车和使用流体动力系统的涡轮机。 汽缸 制动汽缸是一种将流体动力转换成线性或直线、力和运动的装置。因为线性运 动是沿着一条直线前后移动的往复运动。这种类型的制动器有时被称为一个往 复、或线性、电动机
2、。由ram 或活塞组成的汽缸在一个圆柱孔内操作。制动汽 缸可以安装,以便汽缸被固定在一个固定的结构,ram 或活塞被连接到该机制 来操作,或者是活塞和ram 可能被固定到固定结构,汽缸附加到机械装置来操 作。制动汽缸气动和液压系统的设计和操作是类似的。一些变化的ram 和活塞 式制动汽缸的内容将在后面的段落中描述。 冲压式缸 术语 ram 和活塞通常可以互换使用。然而,一个冲压式缸通常被认为是一个截 面积活塞杆超过一半的截面积活动元件。在大多数这种类型的制动汽缸中,杆 和活动元件各占一半。这种类型的活动元件经常被称为柱塞。冲压式缸主要是 用来推动而不是拉。一些应用程序需要ram 的一部分在平坦
3、的外部来推动或升 降单位操作。其他应用程序需要一些机械装置的附件,如一个U 型夹或有眼螺 栓。冲压式缸的设计在很多其他方面不同,以满足不同应用程序的要求。 单作用千斤顶 单作用千斤顶(如图:10-1)试用力只在一个方向。流体定向的汽缸取代ram 和他外部的弹性元件,将物体举起放在上面。 当流体压力释放后,由于没有规定由流体动力缩回ram。物体的重量或者是一 些机械设备,比如一个弹簧,迫使ram 回到汽缸。这种流体能量就倒回到容器。 单作用冲压式汽缸通常用于液压千斤顶。用于移动飞机的飞行甲板和机库甲板 航空母舰的升降机也使用这种类型的汽缸。在这些升降机中,汽缸是水平安装 的,通过一系列的电缆和捆
4、运行升降机。流体压力产生ram 的外在能量使升降 机运行。当从 ram 中释放出流体压力,升降机的重量迫使ram 回到汽缸。反过 来,这迫使流体回容器。 双作用千斤顶 一个双作用冲压式缸如图10-2。在这个汽缸中,两个中风的ram 都是由加压流 体产生的。它有两个流体端口,每一个都在或是接近汽缸的两端。针对流体压 力的封闭端缸扩展ram 和应用力。撤销 ram 和减少力、流体是指向截然相反的 汽缸。一个四通换向阀是通常用于控制双作用ram。当阀门定位来扩展ram, 加压流体进入端口A,作用于 ram 的地面,加强 ram 的外部力量。 对于在液压系统中的回流管, 或者气动系统中的大气, 通过控
5、制阀门, 高于 ram 边缘的流体是免费流出端口B 的。通常情况下,流体的压力和ram 的中风是相 同的。记得第二章中,力等于压力乘以面积(F=PA) 。注意到不同的领域上的 压力如图 10-2 所示。在扩展中风期间,在ram 适用力的同时,对抗大的表面积 的压力是来自于ram 的地下。在收缩行程的过程中,ram 不需要很大的动力。 作用于 ram 顶面的小面积的压力为收回ram 提供了必要的动力。 伸缩式千斤顶 图 10-3 显示了一个可伸缩的冲压式气缸。 一系列的 ram 是嵌在可伸缩的装配中。 除了最小的 ram,每一个 ram 都是中空的 ,作为下一个较小的ram 的油缸壳。ram 装
6、配主要包括活塞部件 ,它还提供了流体端口。尽管这个装配需要一个小空间的 ram 收回,但是当 ram 扩展的时候,伸缩式行动的组装提供了一个相对长的冲程。 这种型号的汽缸的一个很好的例子是应用在自动倾卸卡车上。它是用来解除前 端的卡车床和转储负载。在吊运作业,最大的力量是所需的初始提升的负载。 随着负载的提升并开始转储,所需的力量越来越少 ,直到负载是完全抛弃。 在提高 循环时,加压流体通过端口A 进入气缸,然后作用在ram 的底部表面。 Ram 1 有一个更大的表面积,因此提供了更大的力的初始负载,正如Ram 1 完成它的 行程所需的力是减少的,当Ram 2 移动时,提供较小的力需要继续提高
7、负载。 当 ram 2 完成它的行程 ,一个更小的力量是必需的。 是然后 Ram 3 往外移动完成 提高和倾销负载。一些可伸缩的冲压式的汽缸的单作用类型,像前面所讨论的 单作用千斤顶,这些可伸缩的冲压式汽缸通过重力或机械力收回。一些液压千 斤顶配备了可伸缩的ram。这样的千斤顶是用来提升车辆通过更小的间隙到达 所需的高度。其他类型的可伸缩的汽缸,如图10-3 所示,是双作用类型。在这 种类型中 ,流体压力用于扩展和收缩中风。一个四通换向阀是常用的控制操作的 双作用类型。注意在墙上的 ram1 和 2 的小通路。他们提供了一个路径流体流向, 在汽缸上面边缘的ram2 和 3 之间。在附加行程中,
8、 返回流体通过那些小通路和 汽缸外面到达 B 端口。然后流经换向阀来返回线路或蓄水池。撤销ram,流体 压力是通过 B端口直接进入气缸的,然后反作用于三个ram 的边缘的表面区域。 这迫使 ram 收回了位置。流离失所的流体从ram 的另一侧通过 A 端口流出汽缸, 通过换向阀来返回线路或蓄水池。 Fluid Power NAVEDTRA 14105 CHAPTER 10 ACTUATORS One of the outstanding features of fluid power systems is that force, generated by the power supply, c
9、ontrolled and directed by suitable valuing, and transported by lines, can be converted with ease to almost any kind of mechanical motion desired at the very place it is needed. Either linear (straight line) or rotary motion can be obtained by using a suitable actuating device. An actuator is a devic
10、e that converts fluid power into mechanical force and motion. Cylinders, motors, and turbines are the most common types of actuating devices used in fluid power systems. This chapter describes various types of actuating cylinders and their applications, different types of fluid motors, and turbines
11、used in fluid power systems. CYLINDERS An actuating cylinder is a device that converts fluid power to linear, or straight line, force and motion. Since linear motion is a back-and-forth motion along a straight line, this type of actuator is sometimes referred to as a reciprocating, or linear, motor.
12、 The cylinder consists of a ram or piston operating within a cylindrical bore. Actuating cylinders may be installed so that the cylinder is anchored to a stationary structure and the ram or piston is attached to the mechanism to be operated, or the piston or ram may be anchored to the stationary str
13、ucture and the cylinder attached to the mechanism to be operated. Actuating cylinders for pneumatic and hydraulic systems are similar in design and operation. Some of the variations of ram- and piston-type actuating cylinders are described in the following paragraphs. RAM-TYPE CYLINDERS The terms ra
14、m and piston are often used interchangeably. However, a ram-type cylinder is usually considered one in which the cross-sectional area of the piston rod is more than one-half the cross-sectional area of the movable element. In most actuating cylinders of this type, the rod and the movable element hav
15、e equal areas. This type of movable element is frequently referred to as a plunger. The ram-type actuator is used primarily to push rather than to pull. Some applications require simply a flat surface on the external part of the ram for pushing or lifting the unit to be operated. Other applications
16、require some mechanical means of attachment, such as a clevis or eyebolt. The design of ram-type cylinders varies in many other respects to satisfy the requirements of different applications. Single-Acting Ram The single-acting ram (fig. 10-1) applies force in only one direction. The fluid that is d
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 优质文档 优质 文档 液压 系统 液压缸 外文 翻译
链接地址:https://www.31doc.com/p-5300853.html