BS-SP-107-112-1954.pdf
《BS-SP-107-112-1954.pdf》由会员分享,可在线阅读,更多相关《BS-SP-107-112-1954.pdf(10页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS SP 107-112:1954 Incorporating Amendments Nos. 1, 2 and 3 Specifications for Tab washers for unified hexagons for aircraft* *For tab washers for use with British Standard hexagons, see BS SP 41-46, “Tab washers for aircraft.” ICS 49.030.50 ? Licensed Copy: London South Bank Univer
2、sity, London South Bank University, Mon May 07 12:05:25 GMT+00:00 2007, Uncontrolled Copy, (c) BSI BS SP 107-112:1954 These British Standards, having been approved by the Aircraft Industry Standards Committee and endorsed by the Chairman of the Engineering Divisional Council, were published under th
3、e authority of the General Council of the Institution on 31 May 1954 BSI 2007 ISBN 0 580 34425 8 This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from
4、legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages 1 to 4 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside f
5、ront cover. Amendments issued since publication Amd. No.Date of issueComments 2577September 1956 5272July 1964 1712130 April 2007Indicated by a sideline in the margin Licensed Copy: London South Bank University, London South Bank University, Mon May 07 12:05:25 GMT+00:00 2007, Uncontrolled Copy, (c)
6、 BSI BS SP 107-112:1954 BSI 2007i Contents Page 1Scope1 2Materials1 3Heat treatment1 4Dimensions1 5Finish1 6Protective treatment1 7Identification1 Appendix Recommended application of tab washers used with drilled holes4 Figure 1 Straight and angle tab washers2 Figure 2 Tab washers and drilled holes4
7、 Table 1 British Standard numbers and materials1 Licensed Copy: London South Bank University, London South Bank University, Mon May 07 12:05:25 GMT+00:00 2007, Uncontrolled Copy, (c) BSI ii blank Licensed Copy: London South Bank University, London South Bank University, Mon May 07 12:05:25 GMT+00:00
8、 2007, Uncontrolled Copy, (c) BSI BS SP 107-112:1954 BSI 20071 1 Scope These British Standards specify the materials, dimensions and finish of mild steel and corrosion-resisting steel straight, right angle and left angle tab washers for use with Unified hexagons for aircraft. A recommended method of
9、 application when washers are fitted into drilled holes is shown in the Appendix. 2 Materials The washers shall be manufactured from the appropriate material specified in Table 1. The grain of the material shall be at an angle of approximately 45 across the tabs of the washers. 3 Heat treatment Wash
10、ers to BS SP 108, BS SP 110 and BS SP 112 (Chromium-nickel steel) shall be annealed at 1 050 to 1 080 C for 5 to 10 minutes and cooled in still air. 4 Dimensions The washers shall conform to the dimensions specified in Table 2 and shall be supplied with the tabs bent as shown in Figure 1. 5 Finish 5
11、.1 Washers to BS SP 108, BS SP 110 and BS SP 112 shall be barrelled after heat treatment by an approved method agreed with the purchaser to produce a matt finish. 5.2 The washers shall be free from surface defects, scale, pitting and burrs. Tabs after bending shall be free from corrugation, and any
12、abnormal thickening of the width of the tab due to bending shall be removed. 6 Protective treatment Mild steel washers shall be cadmium plated in accordance with the latest issue of Ministry of Supply aircraft process specification D.T.D. 904. 7 Identification a) The washers shall be identified for
13、ordering purposes by the relevant British Standard number (see Table 1), together with the appropriate code letter shown in Table 2, e.g. a corrosion-resisting steel straight tab washer suitable for a 5/8 in. thread would be BS SP 108 Q. b) All washers shall be identified as “Unified” by a rounded p
14、rojection on the periphery complying with the dimensions shown in Table 2. Table 1 British Standard numbers and materials British Standard No. Type of washerMaterial BS SP 107 Straight tab Deep drawing carbon steel sheets and strips (suitable for welding) complying with BS S 511. BS SP 108Chromium-n
15、ickel steel sheets and strips (corrosion resisting) (13 ton 0.1 per cent proof stress) complying with BS S 521. BS SP 109 Right angle tab Deep drawing carbon steel sheets and strips (suitable for welding) complying with BS S 511. BS SP 110Chromium-nickel steel sheets and strips (corrosion resisting)
16、 (13 ton 0.1 per cent proof stress) complying with BS S 521. BS SP 111 Left angle tab Deep drawing carbon steel sheets and strips (suitable for welding) complying with BS S 511. BS SP 112Chromium-nickel steel sheets and strips (corrosion resisting) (13 ton 0.1 per cent proof stress) complying with B
17、S S 521. Licensed Copy: London South Bank University, London South Bank University, Mon May 07 12:05:25 GMT+00:00 2007, Uncontrolled Copy, (c) BSI BS SP 107-112:1954 2 BSI 2007 Surfaces within diameter S shall be flat within 0.005 in. and uniform in thickness. Figure 1 Straight and angle tab washers
18、 Licensed Copy: London South Bank University, London South Bank University, Mon May 07 12:05:25 GMT+00:00 2007, Uncontrolled Copy, (c) BSI BS SP 107-112:1954 BSI 20073 DIMENSIONS AND CODE LETTERS To suit nominal thread size Code letter Inner diameter Outer diameter ThicknessLarge tabSmall tab Dia. o
19、f flat area of washer Identification pip ABCaDEFGHKRLMNPQST max. min. max. min. Carbon steel washers Corrosion- resisting steel washers 0.010 0.010 2 0 +0.005 0.005 0.010 0.005 No. 8 (.313 Hex size) A.175.170.320.310.022 (24SWG) .175.275.160.037.01550.180.080.080.186.037.025.315.335 No. 10 (.344 Hex
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS SP 107 112 1954
链接地址:https://www.31doc.com/p-3747876.html