BS-EN-2066-2002.pdf

BRITISH STANDARD AEROSPACE SERIES BS EN 2066:2002 Extruded section in aluminium alloys General tolerances The European Standard EN 2066:2001 has the status of a British Standard ICS 49.025.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:33:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2066:2002 This British Standard, having been prepared under the direction of the Engineering Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 07 January 2002 © BSI 07 January 2002 ISBN 0 580 38027 0 National foreword This British Standard is the official English language version of EN 2066:2001. The UK participation in its preparation was entrusted to Technical Committee ACE/61, Inspection and testing requirements for aerospace metallic materials, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 8, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:33:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 2066 December 2001 ICS 49.025.20 English version Aerospace series - Extruded section in aluminium alloys - General tolerances Série aérospatiale - Profilés filés en alliages d'aluminium - Tolérances générales Luft- und Raumfahrt - Strangpreßprofile aus Aluminiumlegierungen - Allgemeine Toleranzen This European Standard was approved by CEN on 2 May 2001. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels © 2001 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2066:2001 E Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:33:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2066:2001 (E) 2 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2002, and conflicting national standards shall be withdrawn at the latest by June 2002. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:33:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2066:2001 (E) 3 0Introduction This standard is part of the series of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258. 1Scope This standard specifies the general tolerances of: Extruded section in aluminium alloys for aerospace applications. It applies: to sections, standardized or defined by a drawing, the cross section of which, regular or irregular, can be inscribed in a circle of 250 mm (see figure 1), Figure 1 to semi-hollow sections, the dimensional limits of which are indicated in figures 2 and 3. x.y ? 2,5x 2 y.z ? 2,5x 2 Figure 2Figure 3 For sections with higher dimensions or of more complex forms, the tolerances shall be subject to agreement between the manufacturer and purchaser. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:33:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2066:2001 (E) 4 2Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 4258Aerospace series Metallic materials General organization of standardization Links between types of EN standards and their use 3Dimensional tolerances 3.1Transverse cross section To obtain the adequate tolerance, the transverse cross section can be divided into elementary rectangles of dimensions A and B; where A is always the largest dimension of the elementary part and B can be considered as the thickness of the section (see figure 4). Figure 4 a) Tolerances on A See table 1. Table 1 Dimensions in millimetres ATolerances A ?10? 0,25 10?A?18? 0,30 18?A?30? 0,40 30?A?50? 0,50 50?A?80? 0,60 80?A?120? 0,80 120?A?180? 1,20 180?A?250? 1,40 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:33:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2066:2001 (E) 5 These tolerances only apply if B A ? 20. For B A ? 20, tolerances shall be the subject of an agreement between the manufacturer and the user. b) Tolerances on B See table 2. Table 2 Dimensions in millimetres Tolerances on B for: B A ? ? 1010 ? ? A ? ? 1818 ? ? A ? ? 3030 ? ? A ? ? 50 B? 1,5? 0,15? 0,20? 0,20? 0,20 1,5?B?3? 0,20? 0,20? 0,20? 0,25 3?B?6? 0,25? 0,25? 0,25? 0,25 6?B? 10? 0,25? 0,30? 0,30? 0,30 10?B? 18? 0,30? 0,35? 0,35 18?B? 30? 0,40? 0,40 30?B? 50? 0,50 continued Table 2 (concluded) Dimensions in millimetres Tolerances on B for: B 50 ? ? A ? ? 8080 ? ? A ? ? 120120 ? ? A ? ? 180180 ? ? A ? ? 250 B? 1,5? 0,25 1,5?B?3? 0,25? 0,30 3?B?6? 0,30? 0,30 6?B? 10? 0,35? 0,35? 0,35 10?B? 18? 0,40? 0,40? 0,40? 0,45 18?B? 30? 0,45? 0,45? 0,50? 0,50 30?B? 50? 0,50? 0,50? 0,55? 0,60 These tolerances only apply if min. max. B B ? 4. If 4 ? min. max. B B ? 8, the tolerances are increased by: 20 % if B ? 18 mm 10 % if B ? 18 mm 3.2Lengths The tolerance of the sections in fixed length shall be ( 0 20? ) mm. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:33:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2066:2001 (E) 6 3.3Bead seat radius The tolerances of the bead seat radius shall be ? 10 % of the radius value with a minimum tolerance of ? 0,4 mm. 4Form tolerances 4.1Straightness See figure 5. Key 1Plane surface Figure 5 On total length X1, the difference in straightness Y1 shall satisfy: Y1 ? 0,002 ? X1. Locally, on each portion X2 = 400 mm: Y2 ? 0,8 mm. 4.2Transverse flatness See figure 6. The maximum difference of the transverse flatness f shall satisfy the following conditions: f ? 0,006 ? A f ? 0,2 mm Figure 6 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:33:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2066:2001 (E) 7 4.3Angular dimensions The angular dimensions ? shall be measured at the point of origin of the angle, as indicated in figure 7. The angular tolerance ? between the two faces is given in table 3: Figure 7 Table 3 Thickness B a mm Angular tolerance ? ? 1,5? 1,5 ° ? 1,5? 1 ° a In the case of a section with two different thicknesses B, the angular tolerance applicable to the greatest thickness B shall be applied. 4.4Twist The twist V shall be measured as indicated in figure 8. V ? k ? B Figure 8 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:33:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2066:2001 (E) 8 The twist tolerances indicated in table 4 apply to sections with linear masses superior to 0,250 kg/m. Table 4 Dimensions in millimetres Values of coefficient k: Diameter of enveloping circle per meter length k max. on the total length D?250,050,10 25?D?500,040,07 50?D?1000,030,05 100?D?2500,020,04 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:33:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:33:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2066:2002 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-global.com. Standards are also available from the BSI website at http:/www.bsi-global.com. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-global.com. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-global.com. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi-global.com/bsonline. Further information about BSI is available on the BSI website at http:/www.bsi-global.com. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-global.com. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:33:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI