BS-EN-60192-2001 IEC-60192-2001.pdf

BRITISH STANDARD BS EN 60192:2001 IEC 60192:2001 Low pressure sodium vapour lamps Performance specification The European Standard EN 60192:2001 has the status of a British Standard ICS 29.140.20 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 14:14:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60192:2001 This British Standard, having been prepared under the direction of the Electrotechnical Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 25 September 2001 © BSI 25 September 2001 ISBN 0 580 38483 7 National foreword This British Standard is the official English language version of EN 60192:2001. It is identical with IEC 60192:2001. It supersedes BS EN 60192:1993 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee CPL/34, Lamps and related equipment, to Subcommittee CPL/34/1, Electric lamps, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. From 1 January 1997, all IEC publications have the number 60000 added to the old number. For instance, IEC 27-1 has been renumbered as IEC 60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 14, lamp data sheets, the annex ZA page and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 14:14:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARDEN 60192 NORME EUROPÉENNE EUROPÄISCHE NORMJuly 2001 CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels © 2001 CENELEC -All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60192:2001 E ICS 29.140.30Supersedes EN 60192:1993 + A4:1995 + A5:1995 English version Low pressure sodium vapour lamps Performance specifications (IEC 60192:2001) Lampes à vapeur de sodium à basse pression Prescriptions de performance (CEI 60192:2001) Natriumdampf-Niederdrucklampen - Anforderungen an die Arbeitsweise (IEC 60192:2001) This European Standard was approved by CENELEC on 2001-07-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 14:14:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 29106:2001- 2 - Foreword The text of document 34A/953/FDIS, future edition 3 of IEC 60192, prepared by SC 34A, Lamps, of IEC TC 34, Lamps and related equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60192 on 2001-07-01. This European Standard supersedes EN 60192:1993 + A4:1995 + A5:1995. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement(dop)2002-04-01 latest date by which the national standards conflicting with the EN have to be withdrawn(dow)2004-07-01 Annexes designated “normative“ are part of the body of the standard. Annexes designated “informative“ are given for information only. In this standard, annexes A, B and ZA are normative and annex C is informative. Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60192:2001 was approved by CENELEC as a European Standard without any modification. _ 1002:29106 NE 2 Page 2 EN 60192:2001 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 14:14:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI CONTENTS 1General 4 1.1Scope. 4 1.2Normative references 4 1.3Definitions 5 1.4Lamp requirements . 6 1.4.1General. 6 1.4.2Dimensions. 6 1.4.3Caps. 6 1.4.4Starting characteristics 6 1.4.5Electrical characteristics 6 1.4.6Photometric characteristics . 6 1.5Information for luminaire design 6 Annex A (normative)Method of measuring starting characteristics 7 Annex B (normative)Method of measuring electrical and photometric characteristics 8 Annex C (informative)Information for luminaire design 10 Bibliography 11 2Data Sheets13 2.1General principles of numbering sheets13 2.2Lists of data sheets13 2.2.1List of lamp data sheets .13 2.2.2List of maximum lamp outline sheets13 Page 3 EN 60192:2001 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 14:14:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI LOW-PRESSURE SODIUM VAPOUR LAMPS PERFORMANCE SPECIFICATIONS 1 General 1.1 Scope This standard specifies the performance requirements for low-pressure sodium vapour lamps for general lighting purposes. For some of the requirements given in this standard, reference is made to “the relevant lamp data sheet”. For some lamps these data sheets are contained in this standard. For other lamps, falling under the scope of this standard, the relevant data are supplied by the lamp manufacturer or responsible vendor. The requirements of this standard relate only to type testing. NOTE The requirements and tolerances permitted by this standard correspond to testing of a type test sample submitted by the manufacturer for that purpose. In principle this type test sample should consist of units having characteristics typical of the manufacturers production and being as close to the production centre point values as possible. It may be expected with the tolerances given in the standard that products manufactured in accordance with the type test sample will comply with the standard for the majority of production. Due to the production spread however, it is inevitable that there will sometimes be products outside the specified tolerances. For guidance on sampling plans and procedures for inspection by attributes, see IEC 60410. 1.2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of IEC and ISO maintain registers of currently valid International Standards. IEC 60050(845), International Electrotechnical Vocabulary (IEV) Chapter 845: Lighting IEC 60061-1, Lamp caps and holders together with gauges for the control of interchangeability and safety Part 1: Lamp caps IEC 60923, Auxiliaries for lamps Ballasts for discharge lamps (excluding tubular fluorescent lamps) Performance requirements IEC 62035, Discharge lamps (excluding fluorescent lamps) Safety specifications 1002:29106 NE 4 Page 4 EN 60192:2001 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 14:14:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 1.3 Definitions For the purposes of this International Standard, the following terms and definitions, as well as others given in IEC 60050(845), apply: 1.3.1 low pressure sodium (vapour) lamp discharge lamp in which the light is produced by radiation from sodium vapour operating at a partial pressure of 0,1 to 1,5 pascal IEV 845-07-24 1.3.2 nominal value approximate quantity value used to designate or identify a lamp 1.3.3 rated value quantity value for a characteristic of a lamp for specified operating conditions. The value and the conditions are specified in this standard, or assigned by the manufacturer or responsible vendor 1.3.4 lamp designation: type E Code, indicating economy, to designate a type of low-pressure sodium vapour lamp with improved luminous efficacy NOTE As these lamps may be operated on various ballasts with slightly different wattages, it is not satisfactory to designate them with a nominal wattage. A lamp designation has been chosen consisting of the letter E and a number approximately numerically equal to their rated wattage. The number in the designation is different from that of the rated wattage, in order to avoid confusion with the existing lamps designated with their nominal wattage. 1.3.5 lamp starting voltage r.m.s. voltage at lamp terminals at which the lamp starts 1.3.6 initial readings starting characteristics of a lamp, measured before ageing, and the electrical and photometric characteristics of a lamp, measured at the end of the ageing period 1.3.7 reference ballast special inductive type ballast, designed for the purpose of providing comparison standards for use in testing ballasts, for the selection of reference lamps and for testing regular production lamps under standardised conditions. It is essentially characterized by the fact that at its rated frequency, it has a stable voltage/current ratio which is relatively uninfluenced by variations in current, temperature and magnetic surroundings, as outlined in the relevant ballast standard 1.3.8 calibration current of a reference ballast value of the current on which the calibration and control of the reference ballast are based 1002:29106 NE 5 Page 5 EN 60192:2001 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 14:14:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 1.3.9 type test test or a series of tests made on a type test sample for the purpose of checking compliance of the design of a given product with the requirements of the relevant standard 1.3.10 type test sample sample consisting of one or more similar units submitted by the manufacturer or the responsible vendor for the purpose of a type test 1.4 Lamp requirements 1.4.1 General A lamp, on which compliance with this standard is claimed, shall comply with the requirements of IEC 62035. A lamp shall be so designed that its performance is reliable in normal and accepted use. In general, this can be achieved by satisfying the requirements of the following subclauses. The requirements given apply to 95 % of production. 1.4.2 Dimensions The dimensions of a lamp shall comply with the values specified on the relevant lamp data sheet. 1.4.3 Caps The cap on a finished lamp shall comply with IEC 60061-1. 1.4.4 Starting characteristics A lamp shall start within the starting time specified on the relevant lamp data sheet and remain alight for at least 1 min. The test shall be made before ageing, using the measuring method given in annex A. 1.4.5 Electrical characteristics The initial readings of the voltage at lamp terminals and of the power dissipated by a lamp shall not exceed the maximum values specified on the relevant lamp data sheet, using the measuring method given in annex B. 1.4.6 Photometric characteristics The initial reading of the luminous flux of a lamp shall be not less than 90 % of the rated value, using the measuring method given in annex B. 1.5 Information for luminaire design Refer to annex C for information for luminaire design. 1002:29106 NE 6 Page 6 EN 60192:2001 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 14:14:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Annex A (normative) Method of measuring starting characteristics A.1 General Lamps shall not be operated during the 5 h immediately prior to making this test. Lamps shall be tested in a circuit as shown in figure A.1, at an ambient temperature between 20 ?C and 30 ?C, using a nominal 50 Hz or 60 Hz supply as appropriate. The ballast used shall satisfy the requirements of IEC 60923. During the test, lamps shall be at a sufficient distance from any earthed metal or starting aid. A.2 Measurement With switch S1 closed and switch S2 open, the voltage measured by voltmeter V1 shall be set to the starting voltage given on the relevant lamp data sheet, and then switch S2 shall be closed. After the test, switch S1 shall be opened before switching off the lamp. Key 1. Supply 2. Ballast 3. Lamp Figure A.1 Circuit diagram for starting test 1 2 V1 S1 S2 3 IEC 525/01 1002:29106 NE 7 Page 7 EN 60192:2001 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 14:14:39 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Annex B (normative) Method of measuring electrical and photometric characteristics B.1 General Lamps shall be tested in a circuit as shown in figure B.1, at an ambient temperature of between 20 ?C and 30 ?C, using a nominal 50 Hz or 60 Hz supply as appropriate. Ballasts used for these measurements shall be reference ballasts having a voltage-to-current ratio and power factor as specified on the relevant lamp data sheets and meeting the general requirements for reference ballasts given in IEC 60923. Before initial readings are taken, the lamp shall be aged for 100 h on a ballast that satisfies the requirements of IEC 60923, at the rated voltage and frequency of the ballast. The supply voltage shall not vary by more than ?10 % and the frequency by not more than ?1 Hz. NOTE The a