BS-EN-60603-5-1998 IEC-60603-5-1987.pdf

BRITISH STANDARD BS EN 60603-5:1998 IEC 60603-5: 1987 Connectors for frequencies below 3 MHz for use with printed boards Part 5: Edge-socket connectors and two-part connectors for double-sided printed boards with 2,54 mm (0,1 in) spacing The European Standard EN 60603-5:1998 has the status of a British Standard ICS 31.220.10 Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 06:57:11 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60603-5:1998 This British Standard, having been prepared under the direction of the Electrotechnical Sector Board, was published under the authority of the Standards Board and comes into effect on 15 May 1998 © BSI 05-1999 ISBN 0 580 29300 9 National foreword This British Standard is the English language version of EN 60603-5:1998. It is identical with IEC 60603-5:1987. The UK participation in its preparation was entrusted by Technical Committee EPL/48, Electromechanical components for electronic equipment, to Subcommittee EPL/48/2, Connectors for electronic equipment, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. From 1 January 1997, all IEC publications have the number 60000 added to the old number. For instance, IEC 27-1 has been renumbered as IEC 60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references Attention is drawn to the fact that CEN and CENELEC standards normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 34 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 06:57:11 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60603-5:1998 © BSI 05-1999i Contents Page National forewordInside front cover Foreword2 Text of EN 60603-53 Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 06:57:11 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii blank Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 06:57:11 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 60603-5 February 1998 ICS 31.220.10 Descriptors: Electronic components, electric connectors, printed-circuit cards, connector plugs, bed plates, designation, dimensions, assembling, couplings, tests, standard gauges, characteristics English version Connectors for frequencies below 3 MHz for use with printed boards Part 5: Edge-socket connectors and two-part connectors for double-sided printed boards with 2,54 mm (0,1 in) spacing (IEC 60603-5:1987) Connecteurs pour fréquences inférieures à 3 MHz pour utilisation avec cartes imprimées Partie 5: Connecteurs encartables et connecteurs enfichables pour cartes imprimées double face au pas de 2,54 mm (0,1 in) (CEI 60603-5:1987) Steckverbinder für gedruckte Schaltungen für Frequenzen unter 3 MHz Teil 5: Steckverbinder für direktes Stecken und indirekte Steckverbinder für beidseitig-beschichtete leiterplatten mit 2,54 mm (0,1 in) Kontaktabstand (IEC 60603-5:1987) This European Standard was approved by CENELEC on 1998-01-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels © 1998 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60603-5:1998 E Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 06:57:11 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-5:1998 © BSI 05-1999 2 Foreword The text of the International Standard IEC 60603-5:1987, prepared by SC 48B, Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic equipment, was submitted to the formal vote and was approved by CENELEC as EN 60603-5 on 1998-01-01 without any modification. The following dates were fixed: Annexes designated “normative” are part of the body of the standard. In this standard, Annex ZA is normative. Annex ZA has been added by CENELEC. Endorsement notice The text of the International Standard IEC 60603-5:1987 was approved by CENELEC as a European Standard without any modification. Contents Page Foreword2 1Scope3 2IEC type designation4 3Common features5 4Dimensions7 5Gauges and test fixtures18 6Characteristics25 7Test schedule26 Annex ZA (normative) Normative references to international publications with their corresponding European publications34 latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement(dop) 1998-12-01 latest date by which the national standards conflicting with the EN have to be withdrawn(dow) 1998-12-01 Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 06:57:11 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-5:1998 © BSI 05-19993 This standard shall be used in conjunction with IEC Publication 512: Electromechanical Components for Electronic Equipment: Basic Testing procedures and Measuring Methods. 1 Scope This standard covers a range of connectors with 2.54 mm (0.1 in) spacing intended to connect a double sided printed board to another printed board or wires. Two kinds of connector are available: One-part edge-socket connector. Fixed connector or (female) receptacle is intended to mate with edge board contacts. Two-part connector. Fixed connector or (female) receptacle is intended to mate with free connector of board-mounted (male) connector. For these two cases, fixed connectors or (female) receptacles are the same. Fixed connectors are available with: solder terminations for wire, solder terminations for board up to 3.44 mm (0.135 in), wrapped terminations. Free connectors are provided with flat solder terminations for double sided board of nominal thickness 1.6 mm (0.063 in). For edge-socket connectors only, polarization and coding are available by means of a device mounted instead of two opposite contacts. Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 06:57:11 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-5:1998 4 © BSI 05-1999 2 IEC type designation Connectors according to this publication shall be designated by: NOTE“L” for letter. “N” for number. Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 06:57:11 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-5:1998 © BSI 05-19995 3 Common features 3.1 Isometric view 3.1.1 Edge-socket connector Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 06:57:11 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-5:1998 6 © BSI 05-1999 3.1.2 Two-part connector Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 06:57:11 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-5:1998 © BSI 05-19997 3.1.3 Common values 3.1.4 Values depending on the number of contacts 3.2 Contact location The contact identification may be partial. It must be made on the front and rear faces for the fixed connectors and on the lateral face for the free connector. The fixed connector contacts may be replaced on the front face of the insulating housing. 4 Dimensions 4.1 General Dimensions in millimetres are original. Drawings are shown in first angle projection. The shape of the connectors may deviate from those given in the following drawings as long as the specified dimensions are not influenced. Reference letter Dimensions Legend mmin a12.540.1Pitch of the terminations of the fixed connector a22.540.1Pitch of the terminations of the free connector or of the contact pads of the double sided board b15.080.2Distance between two rows F10.2 min.0.402 min.Minimum width of mounting cut-out F110 max.0.394 max.Maximum overall width of the fixed connector H214.80.583Distance between the reference plane of the free connector and the touching face of board with free connector M19.30.760Distance between the mounting plane of the fixed connector and the touching face of board with free connector M14.50.177Distance between the mounting plane of the fixed connector and the bottom of the board slot v12.20.480Minimum cut-out of the printed board Reference letter Legend C1Maximum overall length of the fixed connector C2Maximum overall length of the free connector fMinimum length of mounting cut-out N2Maximum length of the printed board in the area of the edge-board contacts X1Distance between the two mounting holes of the fixed connector X2Distance between the two mounting holes of the free connector Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 06:57:11 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-5:1998 8 © BSI 05-1999 4.2 Fixed connector 4.2.1 Insulating housing Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 06:57:11 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-5:1998 © BSI 05-19999 A1B1D1F1K1M1a1b1c1d1e1g1h1 mm 166,953,3100,54,7 mm 2,545,082,0551,85,81,1 146,753,2max.0,44,31,853,50,8min.0,9 in 0.6300.2740.1300.3940.0200.185 in 0.10.20.0810.1970.0710.2280.043 0.5310.2660.126max.0.0160.1690.0730.1380.031min.0.035 Number of contacts 385062748698 mminmminmminmminmminmmin C1 692.71784,23.31599,53.917114,74.516129,95.114145,25.717 682.67783,23.27698,53.878113,74.476128,95.075144,25.677 G145,721.80060,962.40076,203.00091,443.600106,684.200121,924.800 L1 54,72.154702.75685,23.354100,53.957115,74.5551315.157 54,22.13469,52.73684,73.3341003.937115,24.535130,55.137 N1 50,82.00066,12.60281,33.20196,63.803111,84.4021275.000 50,61.99265,92.59481,13.19396,13.795111,64.394126,84.992 X1 62,152.44777,353.04592,653.648107,854.246123,054.844138,355.447 61,852.43577,053.03392,353.636107,554.234122,754.832138,055.435 f1 48,41.90663,642.50678,883.10694,123.706109,364.306124,604.906 min.min.min.min.min.min.min.min.min.min.min.min. Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 06:57:11 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-5:1998 10 © BSI 05-1999 4.2.2 Terminations of fixed connector C = for solder termination for wire Eyelet solder terminations enable the connection of a wire, the conductor of which has a maximum diameter of 0.55 mm (0.022 in). W = for wrapped terminations Wrap posts enable the connection of wires, the conductor of which has a diameter of 0.25 mm (0.010 in), 0.32 mm (0.013 in) or 0.4 mm (0.016 in) on three levels. The cross-section of the wrap post shall have a diagonal between 0.78 mm (0.039 in) and 0.89 mm (0.035 in). Y = for solder terminations for printed board The cross-section of the terminations shall enable its insertion into the holes of the board specified in Sub-clause 4.6.2. mmin T1 5,5 4,5 0.217 0.177 mmin S1 13,2 min. 0.520 min. U1 16 15 0.630 0.591 mmin S1 3.5 min. 0.138 min. V1 5 4 0.197 0.157 Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 06:57:11 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-5:1998 © BSI 05-199911 4.3 Free connector Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 06:57:11 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-5:1998 12 © BSI 05-1999 A2B2D2E2F2H2 mm 12 11,7 3,1 2,9 2,8 2,6 6,5 4,5 0,5 5,5 15,1 14,5 in 0.472 0.461 0.122 0.114 0.110 0.102 0.256 0.177 0.335 0.217 0.594 0.571 a2c2d2e2g2m2n2P2q2r2S2 mm 2,541,83,50,8103,01,5552,053,51,6 1,4max.max.min.max.1,35max.1,851 in 0.10.0710.1380.0310.3940.1180.0610.1970.0810.1380.063 0.055max.max.min.max.0.053max.0.0730.040 Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 06:57:11 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-5:1998 © BSI 05-199913 Number of contacts 385062748698 mminmminmminmminmminmmin C2 62,582.46477,823.06493,063.664108.34.264123,544.864138,785.464 61,582.42476,823.02492,063.624107.34.244122,544.824137,785.424 G245,721.80060,962.40076,203.00091,443.600106,684.200121,924.800 N2 50,51.98865,82.591813.18996,33.791111,54.390126,74.988 50,31.98065,62.58380,83.18196,13.783111,34.382126,54.980 X2 56,082.20871,322.80886,563.408101,804.008117,044.608132,285.208 55,682.19270,922.79286,163.392101,403.992116,644.592131,885.192 f2 501.96965,242.56980,483.16995,723.769110,964.369126,24.969 47,501.87062,742.47077,983.07093,223.670108,464.270123,704.870 NOTE 1Dimension on insert dimension on contacts. NOTE 2Security of insertion according to reference plan. NOTE 3The contact tails shall ensure a sufficient pressure on the board of nominal thickness 1.6 mm (0.063 in) and will be tin-soldered before insertion. Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 06:57:11 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-5:1998 14 © BSI 05-1999 4.4 Mating information The free connector must bottom on the board slot of the fixed connector. 4.5 Polarizing and coding For edge-socket connector only, the polarization can be provided by replacing two opposite contacts of the fixed connector by a polarizing key. A slot shall then be provided in the board to receive it. The place of the polarizing key s