BS-EN-60603-6-1998 IEC-60603-6-1987.pdf

BRITISH STANDARD BS EN 60603-6:1998 IEC 60603-6: 1987 Connectors for frequencies below 3 MHz for use with printed boards Part 6: Edge-socket connectors and printed board connectors with 2,54 mm (0,1 in) contact spacing for single or double-sided printed boards of 1,6 mm (0,063 in) nominal thickness The European Standard EN 60603-6:1998 has the status of a British Standard ICS 31.220.10 Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60603-6:1998 This British Standard, having been prepared under the direction of the Electrotechnical Sector Board, was published under the authority of the Standards Board and comes into effect on 15 May 1998 © BSI 05-1999 ISBN 0 580 29299 1 National foreword This British Standard is the English language version of EN 60603-6:1998. It is identical with IEC 60603-6:1987. The UK participation in its preparation was entrusted by Technical Committee EPL/48, Electromechanical components for electronic equipment, to Subcommittee EPL/48/2, Connectors for electronic equipment, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. From 1 January 1997, all IEC publications have the number 60000 added to the old number. For instance, IEC 27-1 has been renumbered as IEC 60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references Attention is drawn to the fact that CEN and CENELEC standards normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 38 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60603-6:1998 © BSI 05-1999i Contents Page National forewordInside front cover Foreword2 Text of EN 60603-63 Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii blank Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 60603-6 February 1998 ICS 31.220.10 Descriptors: Electronic components, electric connectors, printed-circuit cards, connector plugs, designation, dimensions, assembling, couplings, tests, standard gauges, characteristics English version Connectors for frequencies below 3 MHz for use with printed boards Part 6: Edge-socket connectors and printed-board connectors with 2,54 mm (0,1 in) contact spacing for single or double-sided printed boards of 1,6 mm (0,063 in) nominal thickness (IEC 60603-6:1987) Connecteurs pour fréquences inférieures à 3 MHz pour utilisation avec cartes imprimées Partie 6: Connecteurs encartables et pour cartes imprimées à écartement des contacts de 2,54 mm (0,1 in) pour cartes imprimées simple ou double face, ayant une épaisseur nominale de 1,6 mm (0,063 in) (CEI 60603-6:1987) Steckverbinder für gedruckte Schaltungen für Frequenzen unter 3 MHz Teil 6: Direkte Steckverbinder und Steckverbinder für gedruckte Schaltungen mit 2,54 mm (0,1 in) Kontaktabstand für ein- oder beidseitig beschichtete Leiterplatten mit 1,6 mm (0,063 in) Nenndicke (IEC 60603-6:1987) This European Standard was approved by CENELEC on 1998-01-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels © 1998 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60603-6:1998 E Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-6:1998 2 © BSI 05-1999 Foreword The text of the International Standard IEC 60603-6:1987, prepared by SC 48B, Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic equipment, was submitted to the formal vote and was approved by CENELEC as EN 60603-6 on 1998-01-01 without any modification. The following dates were fixed: Annexes designated “normative” are part of the body of the standard. In this standard, Annex ZA is normative. Annex ZA has been added by CENELEC. Endorsement notice The text of the International Standard IEC 60603-6:1987 was approved by CENELEC as a European Standard without any modification. Contents Page Foreword2 1Scope3 2IEC type designation3 3Common features5 4Dimensions8 5Gauges24 6Characteristics28 7Test schedule29 Annex ZA (normative) Normative references to international publications with their corresponding European publications38 latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement(dop) 1998-12-01 latest date by which the national standards conflicting with the EN have to be withdrawn(dow) 1998-12-01 Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-6:1998 © BSI 05-19993 1 Scope This standard covers a range of connectors with 2.54 mm (0.1 in) contact spacing intended to connect a single or double-sided printed board to another printed board or wires. Two kinds are available: Edge-socket connector A connector with female contacts intended to mate with edge-board contacts and with printed-board connectors having male contacts. Edge-socket connectors are available with: solder terminations for wire; solder terminations for board mounting; wrap terminations. Printed-board connector A connector having male contacts which when mounted on a printed board replaces the edge-board contacts. Printed-board connectors are provided with solder terminations for single or double-sided boards of 1.6 mm (0.063 in) nominal thickness. An edge-socket connector mated with a printed-board connector is referred to as a two-part connector in this standard. The mandatory method of locating is by means of a guide key which replaces an opposite pair of contacts, and one such key is provided per connector (see also Sub-clause 4.5) This standard shall be used in conjunction with the following IEC publications: 2 IEC type designation Nos. 50 (581)(1978):International Electrotechnical Vocabulary, Chapter 581: Electromechanical Components for Electronic Equipment 603-1 (1981): Connectors for Frequencies Below 3 MHz for Use with Printed Boards, Part 1: General Rules and Guide for the Preparation of Detail Specifications. 512-2 (1976): Electromechanical Components for Electronic Equipment; Basic Testing Procedures and Measuring Methods, Part 2: General Examination, Electrical Continuity and Contact Resistance Tests, Insulation Tests and Voltage Stress Tests. 512-3 (1976): Part 3: Current-carrying Capacity Tests. 512-6 (1984): Part 6: Climatic Tests and Soldering Tests. 512-7 (1978): Part 7: Mechanical Operating Tests and Sealing Tests. Amendment No. 1 (1983). Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-6:1998 4 © BSI 05-1999 No. of detail specification/IEC: 603-6 IEC Style:As shown in Clauses 3 and 4 of this standard. Number of ways:Digits denoting the number of contact locations along one side of the connector. Maximum 85 for Styles 1, 2, 3 and 5, and 80 for Style 4. Single or double-sided and active contact row: A = single-sided, side A active, single row of terminations B = single-sided, side B active, single row of terminations E = single-sided, side A active, double row of terminations F = single-sided, side B active, double row of terminations D = double-sided, both sides active Termination style:S = solder terminations for wire B = solder terminations for printed board W = wrap terminations T = through-board solder, short termination L = through-board solder, long termination X = through-board solder, extra long termination Contact finish:A = gold alloy Contact removal/replacement system: A = rear release/front removable/replaceable contacts B = rear release/rear removable/replaceable contacts C = front release/front removable/replaceable contacts D = front release/rear removable/replaceable contacts Variant:Digits identifying individual connector, parts and associated tools for replacement purposes. Example of type designation:603-6 IEC A 80 B W A C XX Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-6:1998 © BSI 05-19995 3 Common features 3.1 Perspective views 3.1.1 Edge-socket connector Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-6:1998 6 © BSI 05-1999 3.1.2 Printed-board connector Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-6:1998 © BSI 05-19997 3.1.3 Values Reference letterLegend a1Pitch of terminations of printed-board connector a2Pitch of contacts of edge-socket connector b2Distance between two rows C1Maximum overall length of printed-board connector C2 C3Maximum overall length of edge-socket connector C4 DMaximum overall width of edge-socket connector H1Distance between mating face of printed-board connector and board M2 M3Distance between mounting plane of edge-socket connector and bottom of board slot M4 WMinimum length of mounting cut-out XDistance between fixing holes of edge-socket connector ZMinimum width of mounting cut-out Reference letterPrinted-board connector Edge-socket connector Edge-socket connector metal feet Edge-socket connector closed ends Style 5Styles 1 and 2Style 3Style 4 C1 max.2.54 n + 0.43 (0.1 n + 0.017) C2 max.2.54 n + 6 (0.1 n + 0.236) C3 max.2.54 n + 30 (0.1 n + 1.18) C4 max.2.54n + 29.8 (0.1 n + 1.17) D max.10 (0.394) 10,4 (0.41) 10,4 (0.41) 10,4 (0.41) H113.9/14.5 (0.55/0.57) M2 Style 14.24/6.0 (0.167/0.236) M2 Style 26.0/7.5 (0.236/0.295) M3, M47.3/8.3 (0.29/0.33) WSee page 20 X25.4 n + 16.2 (0.1 n + 0.64) 25.4 n + 16.2 (0.1 n + 0.64) Z min.11 (0.433) 11 (0.433) 11 (0.433) a12.54 (0.1) 2.54 (0.1) 2.54 (0.1) 2.54 (0.1) a22.54 (0.1) 2.54 (0.1) 2.54 (0.1) 2.54 (0.1) b25.08 (0.2) 5.08 (0.2) 5.08 (0.2) 5.08 (0.2) NOTE 1n = number of contact positions along one side of connector. NOTE 2Dimensions in millimetres (inch dimensions in parentheses). Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-6:1998 8 © BSI 05-1999 4 Dimensions 4.1 General Dimensions in millimetres are original. Drawings are shown in third angle projection. The shape of the connectors may deviate from those given in the following drawings as long as the specified dimensions are not influenced. 4.2 Connectors 4.2.1 Edge-socket connector Styles 1 and 2, open-ended. NOTE 1This tolerance should lie within dimensions e2. NOTE 2This measurement should be made with the component mounted in the normal manner. NOTE 3Dimensions j2 should be effective within card slot engagement area. NOTE 4Replacement guide keys and contacts should be identical to the originals. NOTE 5Row identification A and B is mandatory. Numerical marking is typical. Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-6:1998 © BSI 05-19999 Dimensionmmin A2 max.16.30.642 B29.3/7.80.37/0.31 C2 max.2.54 n + 60.1 n + 0.236 F2 max.10.40.41 G2(n 1) × 2.54(n 1) × 0.1 M2 style 14.24/6.00.167/0.236 M2 style 26.0/7.50.236/0.295 a22.540.1 b25.080.2 c2 min.1.850.07 d2 min.3.100.12 e24.3/5.00.17/0.20 f25.05/5.200.199/0.205 g2See page 8 h2 min.0.50.02 j21.58/1.520.062/0.060 NOTEn = number of contact positions along one side of connector (maximum permissible = 85). Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-6:1998 10 © BSI 05-1999 4.2.2 Edge-socket connector, open-ended with metal mounting feet, Style 3 NOTE 1This tolerance zone should lie within dimension M3. NOTE 2These measurements should be made with the components mounted in the normal manner. NOTE 3This dimension should be effective within card slot engagement area. NOTE 4Replacement contacts and guide keys should be identical to the originals. NOTE 5Row identification A and B is mandatory. Numerical marking is typical. Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:31:21 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-6:1998 © BSI 05-199911 Dimensionmmin A3 max.17.60.69 B39.3/7.80.37/0.31 C3 max.2.54 n + 300.1 n + 1.81 D3 min.3.100.12 D max.10.40.41 G3(n 1) × 2.54(n 1) × 0.1 L3 max.2.54 n + 10.10.1 n + 0.40 M37.3/8.30.29/0.33 X2.54 n + 16.20.1 n + 0.64 a32.540.1 b35.080.2 c3 min.1.850.07 d3 min.3.150.12 g3See page 10 h