BS-EN-60966-2-2-1996 IEC-60966-2-2-1992.pdf

BRITISH STANDARD BS EN 60966-2-2:1996 IEC 966-2-2: 1992 Radio frequency and coaxial cable assemblies Part 2-2: Blank detail specification for flexible coaxial cable assemblies The European Standard EN 60966-2-2:1994 has the status of a British Standard ICS 33.120.10 Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 09:36:12 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60966-2-2:1996 This British Standard, having been prepared under the direction of the Electrotechnical Sector Board, was published under the authority of the Standards Board and comes into effect on 15 August 1996 © BSI 11-1998 The following BSI references relate to the work on this standard: Committee reference EPL/46/1 Draft announced in BSI News Update May 1996 ISBN 0 580 26025 9 Committees responsible for this British Standard The preparation of this British Standard was entrusted by Technical Committee EPL/46, Cables, wires and waveguides, RF connectors and accessories for cabling and signalling, to Subcommittee EPL/46/1, Communication cables, upon which the following bodies were represented: AEA Technology British Approvals Service for Cables British Broadcasting Corporation British Cable Makers Confederation British Railways Board British Telecommunications plc Cable Communication Association Confederation of Aerial Industries ERA Technology Federation of the Electronics Industry London Underground Ministry of Defence Society of Cable Television Engineers Amendments issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 09:36:12 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60966-2-2:1996 © BSI 11-1998i Contents Page Committees responsibleInside front cover National forewordii Foreword2 Text of EN 60966-2-23 List of referencesInside back cover Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 09:36:12 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60966-2-2:1996 ii © BSI 11-1998 National foreword This British Standard has been prepared by Subcommittee EPL/46/1 and is the English language version of EN 60966-2-2:1994, Radio frequency and coaxial cable assemblies. Part 2-2: Blank detail specification for flexible coaxial cable assemblies, published by the European Committee for Electrotechnical Standardization (CENELEC). It is identical with IEC 966-2-2:1992 published by the International Electrotechnical Commission (IEC). In the third paragraph of the introduction, replace “IEC publications” by “European Standards”. Replace “IEC 966-1:1988” by “EN 60966-1:1993”. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-reference Publication referred toCorresponding British Standard HD 323 SeriesBS 2011 Series Environmental testing Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 10, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 09:36:12 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 60966-2-2 June 1994 ICS 33.120.10 Descriptors: Radio frequency and coaxial cable assemblies, blank detail specification for flexible cable assemblies English version Radio frequency and coaxial cable assemblies Part 2-2: Blank detail specification for flexible coaxial cable assemblies (IEC 966-2-2:1992) Ensembles de cordons coaxiaux et de cordons pour fréquences radioélectriques Partie 2-2: Spécification particulière cadre pour cordons coaxiaux souples (CEI 966-2-2:1992) Konfektionierte Koaxial- und Hochfrequenz-Kabel Teil 2-2: Vordruck für Bauartspezifikation für flexible konfektionierte Koaxialkabel (IEC 966-2-2:1992) This European Standard was approved by CENELEC on 1994-03-08. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels © 1994 Copyright reserved to CENELEC members Ref. No. EN 60966-2-2:1994 E Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 09:36:12 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60966-2-2:1994 © BSI 11-1998 2 Foreword The CENELEC questionnaire procedure, performed for finding out whether or not the International Standard IEC 966-2-2:1992 could be accepted without textual changes, has shown that no common modifications were necessary for the acceptance as European Standard. The reference document was submitted to the CENELEC members for formal vote and was approved by CENELEC as EN 60966-2-2 on 8 March 1994. The following dates were fixed: Annexes designated “normative” are part of the body of the standard. In this standard, annex ZA is normative. Contents Page Foreword2 Introduction3 Annex ZA (normative) Other international publications quoted in this standard with the references of the relevant European publications10 latest date of publication of an identical national standard(dop) 1995-03-15 latest date of withdrawal of conflicting national standards(dow) 1995-03-15 Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 09:36:12 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60966-2-2:1994 © BSI 11-19983 Introduction This blank detail specification relates to flexible coaxial cable assemblies operating in the transverse electromagnetic mode (TEM). The creation of a uniform layout and style of detail specifications is determined by the use of a blank detail specification pro forma. The detail specification may be prepared by the insertion of data into the pro forma by a national standards organization, by an approved manufacturer or by a user (when prepared by a user, the detail specification shall be submitted to the national authorized institution by an approved manufacturer). This blank detail specification shall be used with the following IEC publications: IEC 966-1:1988, Generic specification for radio frequency and coaxial cable assemblies Part 1: General requirements and test methods. Amendment 1:1990. IEC 966-2-1:1991, Radio frequency and coaxial cable assemblies Part 2-1: Sectional specification for flexible coaxial cable assemblies. Instructions to complete a blank detail specification Detail specifications shall, as far as possible, be written in accordance with the pro forma which has: a front page with a general description and a drawing or isometric sketch of the cable assembly and its possible variants; ratings, characteristics and inspection requirements (those which are not required or specified shall be omitted). Under quality assessment, tests are divided into groups. Whenever possible entire groups shall be either specified or omitted. These groups are: The numbers shown in brackets on this page correspond to the following items of required information, which should be entered in the spaces provided. 1 Name and address of the organization that has prepared the document. 2 IEC document number, issue number and date of issue. 3 Address of the organization from which the document is available. 4 Related documents. 5 Any other reference to the cable assembly, national reference, trade name, etc. 6 A drawing of the cable assembly giving the outline and principal dimensions. The dimensions are considered to be in millimetres unless otherwise specified. NOTEThe symbol “I” may be used to specify the cable length. In this case the detail specification covers cable assemblies of any length and “I” should then be specified in the order. 7 Nominal characteristic impedance of the cable assembly. 8 Frequency range of use of the cable assembly. (D.C. may be used as a lower limit of frequency, indicating that the cable assembly is capable of transmitting d.c., but at d.c. a number of characteristics may neither apply nor be verified by inspection.) 9 Weight, function of the length of the cable assembly. 10 Minimum static inside bending radius of the cable assembly. Also minimum dynamic inside bending radius of the cable assembly, i.e. the bending radius used for the insertion loss and stability of electrical length tests. 11 Climatic category of the cable assembly related to IEC 68. 12 The applicable quality assessment test groups according to Table 1 of the sectional specification (e.g. Ba, Eh, Eb). 13 Description, if applicable, of the components used for the manufacture of the cable assembly. Ba(Basic)Visual and dimensional tests; Eb(Electrical basic)Low frequency operational tests; Eh(Electrical high frequency) High frequency tests; Ep(Electrical phase)Electrical length tests; Ee(Electrical screening effectiveness) Screening effectiveness tests; Ez(Electrical impedance Z) Impedance uniformity tests; Et(Electrical transmission) Power rating test; Mn (Mechanical)Mechanical tests; Vc(Environmental climatic) Climatic tests; Vv(Environmental vibration) Vibration, bumps and shock tests; Vt(Environmental temperature) Humidity, rapid change of temperature and chemical tests; Vf(Environmental flammability) Flammability and water immersion tests. Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 09:36:12 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60966-2-2:1994 4 © BSI 11-1998 14 Variants of the cable assembly may be listed in one detail specification. The variants may differ by colour, connector material, connector sex or type. (Inspection for quality conformance will be the same for all variants whereas the ratings and characteristics can change.) 15 Number of pages of the blank detail specification including the annexes. 16 Ratings and characteristics of the cable assembly. The properties not specified shall be omitted. 17 Reference to the appropriate subclause in the sectional and generic specifications. 18 The value either guaranteed or used for the defined test. 19 All information required by the sectional specification and any remarks considered as important for understanding the test. 20 Test groups (corresponding to box 12 on page 1 of the blank detail specification). 21 Name of test and its subclause number in the sectional and generic specifications. 22 Periodicity of the test. The periodic tests apply only in the case of qualification approval. 23 Inspection level selected from IEC 410. 24 Acceptable quality level selected from IEC 410. 25 Sample size. 26 Acceptance criteria. 27 Test specimen length shall be specified if the length is different to that given in box 6 on page 1 of the blank detail specification or if the length in box 6 is left free with the parameter “I”. Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 09:36:12 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60966-2-2:1994 © BSI 11-19985 1Elaboré par: Prepared by: 2Document n°: Indice/Issue: Date: 3Disponible auprès de: Available from: 4Spécification générique: Generic specification: CEI/IEC 966-1 Spécification intermédiaire: Sectional specification: CEI/IEC 966-2-1 Spécification particulière cadre: Blank detail specification: CEI/IEC 966-2-2 5Références complémentaires: Additional references: Spécification particulière pour un cordon coaxial souple Detail specification for a flexible coaxial cable assembly 6 7Impédance caractéristique: Characteristic impedance: . . . . 8Bande de fréquence: Frequency range: . . . . . à to . . . . GHz 9Masse: Weight . . . . . . g+ . . . . . . g/m 10Rayon de courbure minimal Minimum inside radius pour les pliages statiques: for static bending: . . . . . .mm pour les pliages dynamiques: for dynamic bending: . . . . . .mm 11 Catégorie climatique: Climatic category:. . / . . / . . 12Groupes dessais applicables: Applicable test groups: Ba, Eh, Eb, Ez, Ep, Ee, Mn, Vv, Vc, Vt, Vf. 13 Référence du connecteur/Connector reference number . . . . . . Série/Series . . . . . type . . . . . . sexe/sex . . . . . . du connecteur/of the connector Référence/Reference n° . . . . . . type . . . . . . du câble/of the cable Armure supplémentaire/Additional armour . . . . . . Méthode de marquage/Marking method. . . . . . Marquage/Marking text . . . . . . 14 Variantes/Variants: 15Page 1 sur 7 pages Page 1 of 7 pages Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 09:36:12 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60966-2-2:1994 6 © BSI 11-1998 16171819 Valeurs et caractéristiques à respecter Inspection values, ratings or characteristics Paragraphe Subclause Valeur Value Remarques Remarks Electrique/Electricala Caractéristiques de réflexion Reflection properties 9.1 . . . . . . dB . . . . . . à/to . . . . . . GHz De lune ou des deux extrémités/from one or two ends Uniformité de limpédance Uniformity of impedance9.2. . . . ± . . . . Une impulsion de temps de montée/Rise time of pulse . . . . . . . ps Pertes dinsertion Insertion loss 9.3 . . . dB . . . dB/m . . . . . . à/to . . . . . . GHz Stabilité des pertes dinsertion Insertion loss stability9.4 . . . dB . . . . . . à/to . . . . . . GHz Tours/Cycles . . . . . . Conditionnement/Arrangement . . . . . Temps de propagation Propagation time 9.5. . . ns ± . . . ns/m Fréquence ou temps de montée/Frequency or rise time Stabilité de la longueur électrique Stability of electrical length 9.6. . . . . /GHz . . . . . . à/to . . . . . . GHz Tours pliés/Cycles bent . . . . . . Tours tordus/Cycles twisted . . . . . . Différence de phase Phase difference 9.7+ . . . . /GHzFréquence/Frequency Variation de phase en fonction de la température Phase variation with temperature 9.8. . . . /GHz . . . . . . à/to . . . . . . K . . . . . . à/to . . . . . . GHz Efficacité décran Screening effectiveness 9.9 . . . . M. . . . . . à/to . . . . . . MHz Tension de tenue Voltage proof 9.10. . . . . kV Résistance disolement Insulation