BS-ISO-11783-3-2007.pdf

BRITISH STANDARD BS ISO 11783-3:2007 Tractors and machinery for agriculture and forestry Serial control and communications data network Part 3: Data link layer ICS 35.240.99; 65.060.01 ? Licensed Copy: London South Bank University, London South Bank University, Thu Dec 20 02:56:05 GMT+00:00 2007, Uncontrolled Copy, (c) BSI BS ISO 11783-3:2007 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2007 © BSI 2007 ISBN 978 0 580 55728 6 National foreword This British Standard is the UK implementation of ISO 11783-3:2007. It supersedes BS ISO 11783-3:1998 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee AGE/6, Agricultural tractors and forestry machinery, to Subcommittee AGE/6/1, Agricultural electronics. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments issued since publication Amd. No. DateComments Licensed Copy: London South Bank University, London South Bank University, Thu Dec 20 02:56:05 GMT+00:00 2007, Uncontrolled Copy, (c) BSI Reference number ISO 11783-3:2007(E) INTERNATIONAL STANDARD ISO 11783-3 Second edition 2007-10-01 Tractors and machinery for agriculture and forestry Serial control and communications data network Part 3: Data link layer Tracteurs et matériels agricoles et forestiers Réseaux de commande et de communication de données en série Partie 3: Couche liaison de données BS ISO 11783-3:2007 Licensed Copy: London South Bank University, London South Bank University, Thu Dec 20 02:56:05 GMT+00:00 2007, Uncontrolled Copy, (c) BSI ii Licensed Copy: London South Bank University, London South Bank University, Thu Dec 20 02:56:05 GMT+00:00 2007, Uncontrolled Copy, (c) BSI iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references. 1 3 Terms and definitions. 1 4 General description 1 5 Technical requirements . 2 5.1 Message frame format 2 5.2 Protocol data unit (PDU) 8 5.3 Protocol data unit (PDU) formats 10 5.4 Message types 13 5.5 Message priority . 20 5.6 Bus access 20 5.7 Contention-based arbitration 20 5.8 Error detection 20 5.9 Assignment process for SA and PGN 21 5.10 Transport protocol functions 23 5.11 PDU processing requirements 31 5.12 Application notes 31 Annex A (informative) ISO 11783 PDU processing Typical receive routine 33 Annex B (informative) Transport protocol transfer sequences Examples of connection mode data transfer 34 Annex C (informative) Communication mode examples 40 Bibliography. 42 BS ISO 11783-3:2007 Licensed Copy: London South Bank University, London South Bank University, Thu Dec 20 02:56:05 GMT+00:00 2007, Uncontrolled Copy, (c) BSI iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. ISO 11783-3 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and forestry, Subcommittee SC 19, Agricultural electronics. This second edition cancels and replaces the first edition (ISO 11783-3:1998), which has been technically revised. ISO 11783 consists of the following parts, under the general title Tractors and machinery for agriculture and forestry Serial control and communications data network: Part 1: General standard for mobile data communication Part 2: Physical layer Part 3: Data link layer Part 4: Network layer Part 5: Network management Part 6: Virtual terminal Part 7: Implement messages application layer Part 8: Power train messages Part 9: Tractor ECU Part 10: Task controller and management information system data interchange Part 11: Mobile data element dictionary Part 12: Diagnostics services Part 13: File server Sequence control is to form the subject of a future part 14. BS ISO 11783-3:2007 Licensed Copy: London South Bank University, London South Bank University, Thu Dec 20 02:56:05 GMT+00:00 2007, Uncontrolled Copy, (c) BSI v Introduction ISO 11783 specifies a communications system for agricultural equipment based on the CAN 2.0 B 1 protocol. SAE J 1939 documents1), on which parts of ISO 11783 are based, were developed jointly for use in truck and bus applications and for construction and agriculture applications. Joint documents were completed to allow electronic units that meet the truck and bus SAE J 1939 specifications to be used by agricultural and forestry equipment with minimal changes. General information on ISO 11783 is to be found in ISO 11783-1. The purpose of ISO 11783 is to provide an open, interconnected system for on-board electronic systems. It is intended to enable electronic control units (ECUs) to communicate with each other, providing a standardized system. The International Organization for Standardization (ISO) draws attention to the fact that it is claimed that compliance with this part of ISO 11783 may involve the use of a patent concerning the controller area network (CAN) protocol referred to throughout the document. ISO takes no position concerning the evidence, validity and scope of this patent. The holder of this patent has assured ISO that he is willing to negotiate licences under reasonable and non-discriminatory terms and conditions with applicants throughout the world. In this respect, the statement of the holder of this patent right is registered with ISO. Information may be obtained from: Robert Bosch GmbH Wernerstrasse 51 Postfach 30 02 20 D-70442 Stuttgart-Feuerbach Germany Attention is drawn to the possibility that some of the elements of this part of ISO 11783 may be the subject of patent rights other than those identified above. ISO shall not be held responsible for identifying any or all such patent rights. 1) Society of Automotive Engineers, Warrendale, PA, USA. BS ISO 11783-3:2007 Licensed Copy: London South Bank University, London South Bank University, Thu Dec 20 02:56:05 GMT+00:00 2007, Uncontrolled Copy, (c) BSI blank Licensed Copy: London South Bank University, London South Bank University, Thu Dec 20 02:56:05 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 1 Tractors and machinery for agriculture and forestry Serial control and communications data network Part 3: Data link layer 1 Scope ISO 11783 as a whole specifies a serial data network for control and communications on forestry or agricultural tractors and mounted, semi-mounted, towed or self-propelled implements. Its purpose is to standardize the method and format of transfer of data between sensors, actuators, control elements, and information-storage and -display units, whether mounted on, or part of, the tractor or implement. It is intended to provide open system interconnect (OSI) for electronic systems used by agricultural and forestry equipment. This part of ISO 11783 describes the data link layer and the use of CAN extended data frames by the network. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 11783-1:2007, Tractors and machinery for agriculture and forestry Serial control and communications data network Part 1: General standard for mobile data communication ISO 11783-5, Tractors and machinery for agriculture and forestry Serial control and communications data network Part 5: Network management ISO 11898-1, Road vehicles Controller area network (CAN) Part 1: Data link layer and physical signalling 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 11783-1 apply. 4 General description The data link layer enables the reliable transfer of data across the physical link. This consists of sending the CAN data frame with the necessary synchronization, sequence control, error control and flow control. The flow control is accomplished through a consistent message frame format. BS ISO 11783-3:2007 Licensed Copy: London South Bank University, London South Bank University, Thu Dec 20 02:56:05 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 2 5 Technical requirements 5.1 Message frame format 5.1.1 General The message frame format shall conform to the CAN requirements. The CAN specification referenced throughout this part of ISO 11783 is specified in ISO 11898-1. When there are differences between the CAN specification and this part of ISO 11783, then this part of ISO 11783 shall be the governing document. The CAN document specifies, in an information-routing-related discussion, that controller addresses are not used. While this is true for some applications of CAN it is not true for ISO 11783. The definition of the ISO 11783 network requires that controller addressing be used to prevent multiple controllers from using the same CAN identifier field. Many additional requirements exist in ISO 11783 that are not specified by CAN. ISO 11898-1 specifies two message frame formats: base frame and extended frame. ISO 11898-1 compatibility implies that messages of both formats can potentially be present on a single network, by using certain bit coding which allows for the recognition of the different formats. Up to this point, ISO 11783 also accommodates both message frame formats. However, ISO 11783 only defines a full strategy for standardized communications using the extended frame format. All base frame format messages are for proprietary use following the rules defined in this part of ISO 11783. ISO 11783 controllers shall therefore use the extended frame format. Base frame format messages may reside on the network, but only in accordance with this part of ISO 11783. NOTE Base frame controllers do not respond to network management messages and are not able to support the strategy for standardized communications. The CAN data frame is parsed into different bit fields, as shown in Figure 1. The number and parsing of the bits in the arbitration and control field differs between the CAN base and CAN extended frame messages. CAN base frame messages, as shown in Figure 1 a), contain 11 identifier bits in the arbitration field, whereas the arbitration field of CAN extended frame messages, as shown in Figure 1 b), contain 29 identifier bits. ISO 11783 has further defined the identifier bits in the arbitration field of the CAN message frame formats. These definitions are given in Table 1. 5.1.2 Message frame format according to ISO 11783 (ISO 11898-1 extended frame format) The CAN extended frame message, illustrated by Figure 1, encompasses a single protocol data unit (PDU). The PDU consists of seven predefined fields, assimilated from information provided by the application layer: Priority; Extended Data Page (EDP), Data Page (DP); PDU Format (PF), PDU Specific (PS), which can be Destination Address (DA), Group Extension (GE) or proprietary; Source Address (SA); Data. (See 5.2 for a detailed description of each field and 5.3 for PDU formats.) BS ISO 11783-3:2007 Licensed Copy: London South Bank University, London South Bank University, Thu Dec 20 02:56:05 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 3 a) CAN base frame format b) CAN extended frame format Figure 1 CAN data frames The fields are then packaged into one or more CAN data frames and sent over the physical media to other network controllers. The layers of the OSI model that ISO 11783 supports are shown in Figure 2. It is possible that some parameter group definitions require more than one CAN data frame in order to send their information. BS ISO 11783-3:2007 Licensed Copy: London South Bank University, London South Bank University, Thu Dec 20 02:56:05 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 4 Figure 2 Application of OSI model according to ISO 11783 Table 1 shows the arbitration and control fields of the 29 bit identifier for CAN, 29 bit identifier for ISO 11783 and 11 bit identifier for CAN, and the use of the 11 bit identifier on an ISO 11783 network. A complete definition for each of the bit field assignments according to ISO 11783 is given in 5.3. In ISO 11783, the CAN data frame data field is described as Bytes 1 to 8. Byte 1s MSB (most significant bit), Bit 8, is the first bit sent closest to the data length code (DLC). Byte 8s LSB (least significant bit), Bit 1, is the last of the data bits to be sent and is closest to the cyclic redundancy check (CRC) field. See Figure 3. NOTE Base frame controllers can use source addressing in their arbitration and control fields, but these addresses are not used by ISO 11783 controllers. When the extended data page (EDP) is equal to 1 and the data page (DP) is equal to 1, the CAN frame is identified as an ISO 15765-3 formatted frame. ISO 15765-3 specifies diagnostics on CAN for road vehicles. Therefore, the processing of this specific CAN frame format does not follow the definitions specified in ISO 11783. BS ISO 11783-3:2007 Licensed Copy: London South Bank University, London South Bank University, Thu Dec 20 02:56:05 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 5 Table 1 Mapping of ISO 11783 into CAN arbitration and control fields 29 bit identifier 11 bit identifier Bit number CAN ISO 11783 CAN ISO 11783 b 1 SOF SOF a SOF SOF a 2 ID28 P3 ID11 P3 3 ID27 P2 ID10 P2 4 ID26 P1 ID9 P1 5 ID25 EDP ID8 ID8 a 6 ID24 DP ID7 ID7 a 7 ID23 PF8 ID6 ID6 a 8 ID22 PF7 ID5 ID5 a 9 ID21 PF6 ID4 ID4 a 10 ID20 PF5 ID3 ID3 a 11 ID19 PF4 ID2 ID2 a 12 ID18 PF3 ID1 ID1 a 13 SRR (r) SRR a RTR (x) RTR a (d) 14 IDE (r) IDE a IDE (d) IDE a 15 ID17 PF2 R0 R0 a 16 ID16 PF1 DLC4 DLC4 17 ID15 PS8 DLC3 DLC3 18 ID14 PS7 DLC2 DLC2 19 ID13 PS6 DLC1 DLC1 20 ID12 PS5 21 ID11 PS4 22 ID10 PS3 23 ID9 PS2 24 ID8 PS1 25 ID7 SA8 26 ID6 SA7 27 ID5 SA6 28 ID4 SA5 29 ID3 SA4 3