IEC-60169-28-1994.pdf
NORME CE1 INTERNATIONALE INTERNATIONAL STANDARD IEC 169128 Première édition First edition 1994-02 Connecteurs pour fréquences radioélectriques - Partie 28: Connecteurs coaxiaux pour fréquences radioélectriques avec diamètre intérieur du conducteur extérieur de 5,60 mm (0,220 in) à verrouillage à encliquetage - Impédance caractéristique 75 ohms Radio-frequency connectors - Part 28: Radio-f requency coaxial con nectors with inner diameter of outer conductor of 5,60 mm (0,220 in) with snap-on coupling - Characteristic impedance 75 ohms Numéro de référence Reference number CEIAEC 169-28: 1994 Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=IHS Employees/1111111001, User=listmgr, listmgr Not for Resale, 03/06/2007 06:11:46 MSTNo reproduction or networking permitted without license from IHS -,-,- Numéros des publications Depuis le ler janvier 1997, les publications de la CE1 sont numérotées à partir de 60000. Publications consolidées Les versions consolidées de certaines publications de la CE1 incorporant les amendements sont disponibles. Par exemple, les numéros d'édition 1.0, 1.1 et 1.2 indiquent respectivement la publication de base, la publication de base incorporant l'amendement 1, et la publication de base incorporant les amendements 1 et 2. Validité de la présente publication Le contenu technique des publications de la CE1 est constamment revu par la CE1 afin qu'il reflète l'état actuel de la technique. Des renseignements relatifs à la date de reconfirmation de la publication sont disponibles dans le Catalogue de la CEI. Les renseignements relatifs à des questions à l'étude et des travaux en cours entrepris par le comité technique qui a établi cette publication, ainsi que la liste des publications établies, se trouvent dans les documents ci- dessous: «Site web, de la CEI“ Catalogue des publications de la CE1 Publié annuellement et mis à jour régulièrement (Catalogue en ligne)* Disponible à la fois au 4 t e web, de la CEI* et comme périodique imprimé Bulletin de la CE1 Terminologie, symboles graphiques et littéraux En ce qui concerne la terminologie générale, le lecteur se reportera à la CE1 60050: Vocabulaire Electro- technique international (VEI). Pour les symboles graphiques, les symboles littéraux et les signes d'usage général approuvés par la CEI, le lecteur consultera la CE1 60027: Symboles littéraux utiliser en électrotechnique, la CE1 6041 7: Symboles graphiques utilisables sur le matériel. Index, rele ve et compilation des feuilles individuelles, et la CE1 6061 7: Symboles graphiques pour schémas. * Voir adresse 4 t e web, sur la page de titre. Num be ring As from 1 January 1997 all IEC publications are issued with a designation in the 60000 series. Consolidated publications Consolidated versions of some IEC publications including amendments are available. For example, edition numbers 1.0, 1.1 and 1.2 refer, respectively, to the base publication, the base publication incorporating amendment 1 and the base publication incorporating amendments 1 and 2. Validity of this publication The technical content of IEC publications is kept under constant review by the IEC, thus ensuring that the content reflects current technology. Information relating to the date of the reconfirmation of the publication is available in the IEC catalogue. Information on the subjects under consideration and work in progress undertaken by the technical committee which has prepared this publication, as well as the list of publications issued, is to be found at the following IEC sources: IEC web site“ Catalogue of IEC publications Published yearly with regular updates (On-line catalogue)* Available both at the IEC web site* and as a printed periodical IEC Bulletin Terminology, graphical and letter symbols For general terminology, readers are referred to I EC 60050: international Electrotechnical Vocabulary (IEV). For graphical symbols, and letter symbols and signs approved by the IEC for general use, readers are referred to publications IEC 60027: fetter symbols to be used in electrical technology, IEC 60417: Graphical symbols for use on equipment. Index, survey and compilation of the single sheets and IEC 60617: Graphical symbols for diagrams. * See web site address on title page. Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=IHS Employees/1111111001, User=listmgr, listmgr Not for Resale, 03/06/2007 06:11:46 MSTNo reproduction or networking permitted without license from IHS -,-,- NORME I NTE RN AT I ON ALE INTERNATIONAL STANDARD CE1 IEC 169128 Première édition First edition 1994-02 Connecteurs pour fréquences radioélectriques - Partie 28: Connecteurs coaxiaux pour fréquences radioélectriques avec diamètre intérieur du conducteur extérieur de 5,60 mm (0,220 in) à verrouillage à encliquetage - Impédance caractéristique 75 ohms Radio-frequency connectors - Part 28: Radio-frequency coaxial connectors with inner diameter of outer conductor of 5,60 mm (0,220 in) with snap-on coupling - Characteristic impedance 75 ohms 0 CE1 1994 Droits de reproduction réservés - CopyrigM - all rights resewed Aucune partie de cette publication ne peut surface roughness Ra = 0,4 pn (16 pin ) max. Test procedure Gauge A shall be inserted once only into the female centre contact. This is a sizing operation. After this, Gauge B shall be inserted into the female centre contact. The contact shall support the mass of the gauge in a vertical attitude. Additional test Following the sizing operation, and if prescribed in the Detail Specification, the force necessary to insert Gauge A fully into the female centre contact shall be measured. When this test is required, the maximum permitted insertion force shall then be specified and shall not exceed 11 N. NOTE - (for information only) Gauge A is used for qualification approval tests only. The minimum diameter of gauge A corresponds t o the maxjmum diameter of a male contact pin. Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=IHS Employees/1111111001, User=listmgr, listmgr Not for Resale, 03/06/2007 06:11:46 MSTNo reproduction or networking permitted without license from IHS -,-,- - 14- 3.2.2 Calibre pour contact extérieur de la fiche Calibre A - Conditions maximales de matière pour calibrage 1 mm I n Plan de réfé- _I Calibre B - Conditions minimales de matière pour ia mesure de ia force de rétention du calibre Masse (poids) du calibre: 800 g f 10 g mm I in 169-28 O CE111994 Variane d'indication des d6taik de ia gorge Figure 4 - Calibres A et B pour calibrage et force de rétention du contact extérieur (Pour les dimensions, voir tableau 2). Tableau 2 I Réf. i min. I max. i min. i max. i I I I I A 0 I 6,236 I 6,251 I 0,2455 I 0,2461 J I 3 3 I 3,s I 0.131 1 0,141 K I 0,579 I 0,0228 LYon I 0,051 I 0.076 I 0,002 I 0,003 A A 0 6,020 6,035 DD 0,002 I 0,006 MMrayon 1 - I 0,13 I - I 0,005 Matériau: acier poli; rugosité Ra = 0,4 pm (1 6 pin ) ma. i min. i max. I min. i max. i I I I 6,172 I 6,185 1 0,2430 I 0,2435 I 3,33 I 3 , s I 0,131 I 0,141 0,579 I 0,0228 0,127 I 0,152 I 0,005 I I I 0,13 l - 7 0,005 - Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=IHS Employees/1111111001, User=listmgr, listmgr Not for Resale, 03/06/2007 06:11:46 MSTNo reproduction or networking permitted without license from IHS -,-,- 169-280 IECz1994 Gauge A - Maximum material - for sizing purposes 1 mm 1 in -15- Gauge B - Minimum material - for measurement of gauge retention force ivïass (weight) of gauge: 800 f 10 g mm I in 3.2.2 Gauge for outer contact of plug Ref. A 0 J K For scrap views, see figures 4a and 4b 0.38 mm (0,015 in) m a . radius 0,125 mm (0,005 in) min. radius or chamfer permbible Figure 4b Hole to allow entry of inner conductorfirnulator of plug o min. max. min. max. 6,236 6,251 0,2455 0,2461 3 3 338 0,131 0,141 0.579 0,0228 Alternative indication of details of groove 6,172 3.33 Figure 4 - Outer contact sizing and retention force gauges A and B (For dimensions, see table 2) 6,185 0,2430 0,2435 3.58 0,131 0,141 Table 2 0,579 0,0228 i min. I max. I min. I max. I 0,127 I 0,152 I 0,005 I 0,006 0,102 0,127 0,004 0,005 0,152 0,178 0,006 0,007 6,020 6,035 0,2370 0,2376 0,69 0,71 0,027 0,028 0,279 0,305 0,011 0,012 0,05 0,15 0,002 0,006 I I Material: steel, polished; surface roughness Ra = 0.4 pn (16 pin ) max. Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=IHS Employees/1111111001, User=listmgr, listmgr Not for Resale, 03/06/2007 06:11:46 MSTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=IHS Employees/1111111001, User=listmgr, listmgr Not for Resale, 03/06/2007 06:11:46 MSTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=IHS Employees/1111111001, User=listmgr, listmgr Not for Resale, 03/06/2007 06:11:46 MSTNo reproduction or networking permitted without license from IHS -,-,- ICs 33.120.30 Typeset and printed by the IEC Central Ofice GENEVA, SWITZERLAND Copyright International Electrotechnical Commission Provided by IHS under license with IECLicensee=IHS Employees/1111111001, User=listmgr, listmgr Not for Resale, 03/06/2007 06:11:46 MSTNo reproduction or networking permitted without license from IHS -,-,-