GMNA-9984169-1992.pdf

- 900b379 0004596 894 I GENERAL MOTORS ENGINEERING STANDARDS I Materials and Processes - Paint 1 PRIMER CHIP RESISTANT, WEATHERABLE, BLACKOUT 9984189 1 SCOPE. This specification covers the requirements for a low bake, thermosetting, chip resistant primer applied by spraying. This materiaI is intended to provide a smooth chip and corrosion resistant coating, for steel or composite sub- strates, when applied over previously applied primer such as cathodic electrocoat. It is intended to protect lower body com- posite or metal surfaces that are subjected to severe gravel impact and also perform as a blackout material without subse- quent topcoating. 2 REFERENCED STANDARDS. GM4356M GM9501P GM4389M GM9505P GM4465M GM9508P GM9071P GM9509P GM9163P GM9543P GM9595P ASTM D1186 ASTM D2246 ASTM D3170 ASTM D3363 3 REQUIREMENTS. The requirements listed below shall be met on all critical surfaces of the part or as designated by the applicable engineering document. These requirements shall be determined on the baked anticbip primer. This primer shall meet Type IU primer requirements of GM4356M. 3.1 FILM THICKNESS (ASTM 01186). The range and tar- get values may vary with each suppliers material. Therefore, these values will be declared by tbe supplier and agreed on with the responsible GM paint engineer prior to the initiation of testing. 3.2 WTHERABILI A . The coating shall be exposed in South Florida (5 south per GM9163P). Teat requimmems for test samples and control (current production) are as follows: 3.2.1 A minimum of 12 months Florida exposure with panels prepared to this specification must retain at least 90% of the original gloss and DOI. In addition there must be no signifi- cant shift in color or adverse appearance change. 4 SUPPLEMENTAL INFORMATION. 4.1 APPLICATION AND BAKE. The material must be capable of being applied from all conventional spray equip ment. Nominal bake for this material is 30 minutes 12O C. Baking within the range of this process specification shall have no effect on product durability. The supplier must provide data showing the viscosity-temperature relationships and circulation stability characteristics of the materials. 4.2 PANEL PREPARATION. A detailed description of the test panel and qualification requirements for the material is covered in this specification. The engineering group responsi- ble for coordinating the material development should always be contacted prior to preparation of panels and initiation of testing to determine if the test program should deviate in any way from the specifted GM4356M and plant application. 4.2.1 A sufftcient number of panels should be prepared to accommodate all required tests; however, some tests may be combined on the same panels. Pretreatment and priming of panels will be established at the beginning of the test pro- grams. All bakes refer to substrate temperature in gas fired ovens. 4.2.2 All bakes are described in Table 1. TABLE 1 - BAKE CHART Bake Normal Primer Time, minutes Temperature, C Target 1 Target Under Over Target 3 x Target Target - 5 C Target + 15 C NOTE: Target is defined as the normal bake temperature and normal time as recommended by the supplier of the primer. Both the supplier and the engineer must agree on the target prior to testing. 5 SOURCE SHIPMENT RESPONSIBILlTY. It will be the rcsponsibiity of the supplier to insure that the material is not exposed to temperatures during shipment which would cause the material to fail to meet any of the requirements of this specification. 8 INlTlAL SOURCE APPROVAL. No shipment shall be made by any supplier until representative initial production samples have been approved by engineering as meeting the requirements of this specification. 6.1 Completed copies of the GM Material Safety Data Sheet and Critical Material Register (available from the engineering department or laboratory), or equivalent, must be submitted with any new submissions or where a composition change has OCCUlTCd. 6.2 SUBMISSION PACKAGE. Four (4) submission pack- ages shall be prepared for distribution. One package should be prepared for each of the 3 GM divisions and one for documen- tation retention to insure corporate product compliance with GM standards. One complete set of test panels shall be retained by the supplier and be available for review as long as the product is in production. The submission packages shall contain a submission letter, panel preparation data, test data, product data sheet, 8 x 10” photographs of each panel and key process control information. The package shall be dated and signed by the GM Corporate Primer Committee acknowledg- ing that the testing procedures complied with this specification. 7 INSPECTlON AND REJECTION. All shipments of material or parts under contract or purchase order manufac- tured to this specificatian shalJ be equivalent in every respect to the initial samples approved by engineering. There shall be no changes in either formulation or manufacturing processes pemitted without prior notification and approval by engineer- ing. Lack of notification by the supplier constitutes grounds for rejection of ariy shipment. While samples may be taken NOVEMBER 1992 PAGE 1 9964169 Copyright General Motors North America Provided by IHS under license with GM Licensee=IHS Employees/1111111001, User=Japan, IHS Not for Resale, 06/23/2008 22:53:56 MDTNo reproduction or networking permitted without license from IHS -,-,- I 9006379 0004597 720 I GENERAL MOTORS ENGINEERING STANDARDS I Materials and Processes - Paint I PRIMER CHIP RESISTANT, WEATHERABLE, BLACKOUi 9984169 from incoming shipments and checked for conformance to this specification, the supplier shall accept the responsibility for incoming shipments meeting this specification without depen- dence upon purchaser s inspection. In addition the supplier shall be responsible for submitting a CERTIFICATE OF ANALYSIS with each batch of material arriving at a plant. This document shall be prepared and provide data in accord- ance with the requirements detailed in -GM4389M. 8 APPROVED SOURCES. Engineering qualification of an approved source is required for this speciftcation. Only sources listed in the GM Materials File under this specification number have been qualified by engineering as meeting the requirements of this specification. Sources are available through the on-line MATSPC System. 9 GENERAL INFORMATION. This standard was oriai- nated by NAO Paint Operations in June 1992. TABLE 2 - TESTS Tests Tape Adhesion (GM9071P) + T/C Overspray* Humidity + Tape Adhesion (GM4465M. GM9071P) + T/C timpray* Gravelometer (GM9508P) + T/C Overspray* Environmental Crack Cycle A (GM9595P. GM9071P) Repair Primer Compatibility; and Final-Lime; Humidity + Tape Adhesion (GM4465M+ GM9071P) Gas Dip (GM9501PI UV Tkansmission, 0.8 mm film (GM9543P) Adequacy of Cure, GM9509P (xylene or a ketone) Gloss lyearFLexposumor3OOOkJin Xenon arc plus; Tape Adhesion (GM9163P + GM9071P) T Primer Film Build NOlTMl NOlld NOlId N0lTM.l NORMI NOlZlEd Normal NOtlMl LOW Normal Normal NormaI I-ah Normal Normal Normal Normal Normal Normal Normal NOItlld NORMI NORMl Bake Normal I-w LOW NOnMI NOKMl High LOW NORMI NORMl LOW Normal High Normal Normal Normal High LOW LOW Normal Normal NOllMl NOIIMl N0Il.d NCllIMl 7 Performance Requirements Min 99% retention Min 99% retention Min 99% retention Min 99% retention Min 99% retention Mill 99% retention Mill 99% retention Mill 99% retention Expected = 8 Bxpected=8 Expected = 8 Expected = 8 Expected = 8 No cracks, blistering, or loss of adhesion Min 80 = retention Expected 90% retention Rating of 1 or less. No color change or softening Min 0% and 360 Nm 0.7% and 410 Nm 5% and 500 Nm 2O%and600Nm No appearance change or softening of film and only a slight color transfer allowed Gloss level (mm 30 on a 20 meter) de&n&& by engineering application Mill 99% retention 9964169 PAGE 2 NOVEMBER 1992 Copyright General Motors North America Provided by IHS under license with GM Licensee=IHS Employees/1111111001, User=Japan, IHS Not for Resale, 06/23/2008 22:53:56 MDTNo reproduction or networking permitted without license from IHS -,-,- I 9006379 0004598 667 I GENERAL MOTORS ENGINEERING STANDARDS I Materials and Processes - Paint I PRIMER CHIP RESISTANT, WEATHERABLE, BLACKOUT 9984169 TABLE 2 - TESTS - Continued Tests Gravelometer (GM9163P + GM9508P) Primer Film Build Bake Performance Requirements LOW Normal Mitlrating=7 Normal Normal Excepted 38 High 1 Normal 1 Excepted =8 *T/C = Topcoat Overspray NOTE: Normal primer is defined, by the supplier, as the target film build for the material. Low and high film build is defined. by the supplier, as the lower and upper processing film builds where material properties are still achievable. NOVEMBER 1992 PAGE 3 9964169 Copyright General Motors North America Provided by IHS under license with GM Licensee=IHS Employees/1111111001, User=Japan, IHS Not for Resale, 06/23/2008 22:53:56 MDTNo reproduction or networking permitted without license from IHS -,-,-