ISO-21000-7-FDAM-1-2008.pdf

Please see the administrative notes on page iii RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE AND TO PROVIDE SUPPORT- ING DOCUMENTATION. IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO- LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STAN- DARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS. Reference number ISO/IEC 21000-7:2007/FDAM 1:2008(E) © ISO/IEC 2008 FINAL DRAFT ISO/IEC JTC 1 Secretariat: ANSI Voting begins on: 2008-09-04 Voting terminates on: 2008-11-04 AMENDMENT ISO/IEC 21000-7:2007 FDAM 1 Information technology Multimedia framework (MPEG-21) Part 7: Digital Item Adaptation AMENDMENT 1: Query format capabilities Technologies de l'information Cadre multimédia (MPEG-21) Partie 7: Adaptation d'article numérique AMENDEMENT 1 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 10/25/2008 21:48:06 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO/IEC 21000-7:2007/FDAM 1:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. Copyright notice This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted under the applicable laws of the user's country, neither this ISO draft nor any extract from it may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission being secured. Requests for permission to reproduce should be addressed to either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Reproduction may be subject to royalty payments or a licensing agreement. Violators may be prosecuted. ii © ISO/IEC 20# All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 10/25/2008 21:48:06 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO/IEC 21000-7:2007/FDAM 1:2008(E) © ISO/IEC 2008 All rights reserved iii In accordance with the provisions of Council Resolution 21/1986, this document is circulated in the English language only. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 10/25/2008 21:48:06 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO/IEC 21000-7:2007/FDAM 1:2008(E) iv © ISO/IEC 2008 All rights reserved Foreword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of the joint technical committee is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. Amendment 1 to ISO/IEC 21000-7:2007 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 29, Coding of audio, picture, multimedia and hypermedia information. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 10/25/2008 21:48:06 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO/IEC 21000-7:2007/FDAM 1:2008(E) © ISO/IEC 2008 All rights reserved 1 Information technology Multimedia framework (MPEG-21) Part 7: Digital Item Adaptation AMENDMENT 1: Query format capabilities In Clause 2, add the following: ISO/IEC 15938-12, Information technology Multimedia content description interface Part 12: Query format In Table 1, append the following row: mpqf urn:mpeg:mpqf:schema:2008 After 6.5.30, insert the following new subclause and renumber the existing 6.5.31 as 6.5.32: 6.5.31 Query Format Capabilities 6.5.31.1 Introduction This subclause specifies the ISO/IEC 15938-12 capabilities that a terminal is capable to provide. 6.5.31.2 Syntax Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 10/25/2008 21:48:06 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO/IEC 21000-7:2007/FDAM 1:2008(E) 2 © ISO/IEC 2008 All rights reserved 6.5.31.3 Semantics Syntax of the MPQFCapabilitiesType: Name Definition MPQFCapabilitiesType Tool for describing the ISO/IEC 15938-12 capabilities a terminal is capable to provide. MPQFCapability Describes the ISO/IEC 15938-12 capabilities of a particular service a terminal is capable to provide. NOTE The service is identified by the serviceID attribute of the mpqf:AvailableCapabilityType. In 6.5.32, Terminal capabilities examples, insert the following text after EXAMPLE 5: EXAMPLE 6 The following example provides an instantiation of the ISO/IEC 15938-12 capabilities of the terminal. urn:mpeg:mpeg7:2004 audio/mp3 video/mpg audio/aac video/mpg Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 10/25/2008 21:48:06 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 10/25/2008 21:48:06 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO/IEC 21000-7:2007/FDAM 1:2008(E) ICS 35.040 Price based on 2 pages © ISO/IEC 2008 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Boeing Co/5910770001 Not for Resale, 10/25/2008 21:48:06 MDTNo reproduction or networking permitted without license from IHS -,-,-