JIS-B-0002-2-1998-R2003-ENG.pdf
JIS JIS B 0002-2:1998 JAPANESE INDUSTRIAL STANDARD Translated and Published by Japanese Standards Association (IS0 6410-2 : 1993) Technical drawings- Screw threads and threaded parts- Part 2 : Screw thread inserts c 1 ICs 01.100.20; 21.040.01 Descriptors : threads, technical drawing, engineering drawings, threaded compo- Reference number : JïS B 0002-2 : 1998 (E) nents, threaded fasteners Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/11/2007 00:26:38 MSTNo reproduction or networking permitted without license from IHS -,-,- B 0002-2 : 1998 (IS0 6410-2 : 1993) Foreword This translation has been made based on the original Japanese Industrial Standard established by the Minister of International Trade and Industry through deliberations at Japanese Industrial Standards Committee in accordance with the Industrial Standardization Law: JIS B 0002 consists of the following parts, under the general title Technical drawings-Screw threads and threaded parts: Part 1 : General conventions Part 2 : Screw thread inserts Part 3 : Simplified representation Date of Establishment: 1998-01-20 Date of Public Notice in Official Gazette: 1998-01-20 Investigated by: Japanese Industrial Standards Committee Divisional Council on Machine Elements JIS B 0002-2: 1998, First English edition published in 1999-08 Translated and published by: Japanese Standards Association 4-1-24, Akasaka, Minato-ku, Tokyo, 107-8440 JAPAN In the event of any doubts arising as to the contents, the original JIS is to be the final authority. 1 L ? ? b O JSA 1999 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. Printed in Japan Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/11/2007 00:26:38 MSTNo reproduction or networking permitted without license from IHS -,-,- JAPANESE INDUSTRIAL STANDARD JIS B 0002-2 : 1998 (IS0 6410-2 : 1993) Technical drawings- Screw threads and threaded parts- Part 2 : Screw thread inserts Introduction This part of JIS B O002 has been prepared on the basis of IS0 6410- 2 , Technical drawings-Screw threads and threaded parts-Part 2 : Screw thread inserts published in 1993 as the first edition, without modifying its technical content. The ?Remarks? and ?Informative references? underlined with dots are items not included in the original International Standard. JIS B o002 has been devised to provide a universal means of communication among the various interests involved in the design, manufacture and installation of fasten- ers. 1 Scope This part of JIS B 0002 specifies methods for the representation of screw thread inserts on technical drawings. 3 Representation 3.1 Detailed representation of the true shape of screw thread inserts The detailed representation of the true shape of screw thread inserts (see Figs. 1 to 3) shall only be used for illustrations, e.g. in catalogues, and should be avoided in tech- nical drawings. Fig. 1 Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/11/2007 00:26:38 MSTNo reproduction or networking permitted without license from IHS -,-,- 2 B 0002-2 : 1998 (IS0 6410-2 : 1993) Fig. 2 Fig. 3 3.2 Conventional representation Screw thread inserts are usually drawn us- ing a conventional representation derived from JIS B 0002-1. The outer forms of screw thread inserts vary greatly depending on the intended purpose, the material, the manufacturer, etc., and may not even be threaded but all shall be depicted in the same way. Examples are shown in Attached Table 1. 3.3 Simplified representation In simplified representation only the essential features shall be shown, depending on the kind of drawing and the purpose of the documentation. The simplified representation for screw thread inserts should be used whenever possible. The principle of simplification is shown in Fig. 4. Different examples and pos- sible identification for simplified representation of inserts are shown in Attached Table 1. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/11/2007 00:26:38 MSTNo reproduction or networking permitted without license from IHS -,-,- ! I- 3 B 0002-2 : 1998 (IS0 6410-2 : 1993) I - - Helical coil insert I I Conventional representation Detailed representation Simplified representation I a I I I Detailed representation d = nominal diameter d i = external crest diameter Fig. 4 Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/11/2007 00:26:38 MSTNo reproduction or networking permitted without license from IHS -,-,- 4 B 0002-2 : 1998 (IS0 6410-2 : 1993) In sections, the outlines of the screw thread insert (external and internal crests) shall be shown by a continuous thick line (in accordance with JIS Z 8312). The nominal diameter of the internal thread in assembled condition shall not be shown. The insert itself shall not be hatched (see Fig. 5). Informative reference : A thick line specified in JIS Z 8312 is equivalent to type A of IS0 128. _. - -_-._._I_ Fig. 5 On an end view, the external and internal crests shall be shown as a full circle by a continuous thick line. The nominal diameter of the internal thread in the assembled condition shall not be shown (see Fig. 6). Fig. 6 4 Designation and dimensioning Screw thread inserts shall be designated as given in the relevant standards. If such standards are not available the designation shall consist of the designation for the thread, d x P (screw thread for which the screw thread insert is intended) followed by the letters INS (for insert). Example : M30 x 1 . 5 INS When a more general description is sufficient, e.g. there is an insert placed, the Remarks 1 If the thread is coarse, the designation of the pitch, P, may be omit- ted. Additional information (manufacturers name, catalogue number, etc.) may be added. The designation may be indicated by means of a leader line (see Fig. 7) or as a abbreviation INS shall be indicated (see Figs. 5 and 6 ) . dimension (see Attached Table i). Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/11/2007 00:26:38 MSTNo reproduction or networking permitted without license from IHS -,-,- 5 B 0002-2 : 1998 (IS0 6410-2 : 1993) Fig. 7 l Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/11/2007 00:26:38 MSTNo reproduction or networking permitted without license from IHS -,-,- 6. B 0002-2 : 1998 (IS0 6410-2 E93) Insert h a through hole ina blind hole ina through hole usembly fanin- - ert ina blind hole Attached Table 1 Representation Detailed Conventional Simplified M OX1.5 NS H /- M30X1.5 INS I Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/11/2007 00:26:38 MSTNo reproduction or networking permitted without license from IHS -,-,- STD-JIS B 0U02-2-ENGL 1998 4933b08 055b774 T53 m Errata for JE (English edition) are printed in standardization joumd, published monthly by the Japanese Standards Association, and also provided to subscribers of JIS (English edition) in Monthly Information. Errata will be provided upon request, please contact: Standardization Promotion Department, Japanese Standards Association 4-1-24, Akasaka, Minato-ku, Tokyo, 107-8440 JAPAN TEL. 03-3583-8002 FAX. 03-3583-0462 Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/11/2007 00:26:38 MSTNo reproduction or networking permitted without license from IHS -,-,-