NF-EN-10080-2005-ENG.pdf
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 10080 May 2005 ICS 77.140.15; 77.140.60; 77.140.65 Supersedes ENV 10080:1995 English version Steel for the reinforcement of concrete - Weldable reinforcing steel - General Aciers pour l'armature du béton - Aciers soudables pour béton armé - Généralités Stahl für die Bewehrung von Beton - Schweißgeeigneter Betonstahl - Allgemeines This European Standard was approved by CEN on 21 April 2005. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels © 2005 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10080:2005: E blank EN 10080:2005 (E) 2 Contents Page Foreword 3 1 Scope.4 2 Normative references .4 3 Terms and definitions.5 4 Symbols.8 5 Designation .10 5.1 Bar, coil and de-coiled product10 5.2 Welded fabric 10 5.3 Lattice girders .12 6 Steelmaking and manufacturing processes .13 7 Performance characteristics13 7.1 Weldability and chemical composition .13 7.2 Mechanical properties 14 7.3 Dimensions, mass and tolerances.17 7.4 Bond strength and surface geometry20 7.5 Verification of performance characteristics22 8 Evaluation of conformity22 8.1 Factory production control 22 8.2 Initial type testing25 8.3 Continuous surveillance of factory production control and audit testing28 8.4 Evaluation, reporting and action30 8.5 Assessment of the long term quality level31 9 Test methods.32 9.1 Bars, coils and de-coiled products32 9.2 Welded fabric 32 9.3 Lattice girders .33 10 Identification of the manufacturer and the technical class33 10.1 Bar33 10.2 Coil.35 10.3 De-coiled product36 10.4 Welded fabric 36 10.5 Lattice girders .36 11 Verification of mechanical properties in the case of dispute36 Annex A (informative) Examples of weld points in lattice girder joints .37 Annex B (normative) Test methods for lattice girders38 Annex C (informative) Bond test for ribbed and indented reinforcing steel Beam test .44 Annex D (informative) Bond test for ribbed and indented reinforcing steel Pull-out test54 Annex E (informative) Comparison of symbols used in this European Standard with those used in EN 1992-1-1 and EN 1992-1-2.61 Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive .62 EN 10080:2005 (E) 3 Foreword This document (EN 10080:2005) has been prepared by Technical Committee ECISS/TC 19 “Concrete reinforcing and pre-stressing steels - Properties, dimensions, tolerances and specific tests”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2005, and conflicting national standards shall be withdrawn at the latest by May 2007. This document has been prepared under Mandate M/115 given to CEN by the European Commission and the European Free Trade Association and supports essential requirements of the EU Construction Products Directive (89/106/EEC). For relationship with the EU Construction Products Directive, see informative Annex ZA, which is an integral part of this document. This document does not apply to non-weldable reinforcing steel. This document does not define technical classes. Technical classes should be defined in accordance with this document by specified values for Re, Agt, Rm/Re, Re,act./Re,nom. (if applicable), fatigue strength (if required), bendability, weldability, bond strength, strength of welded or clamped joints (for welded fabric or lattice girders) and tolerances on dimensions. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 10080:2005 (E) 4 1 Scope 1.1 This European Standard specifies general requirements and definitions for the performance characteristics of weldable reinforcing steel used for the reinforcement of concrete structures, delivered as finished products in the form of: bars, coils (rod, wire) and de-coiled products; sheets of factory-made machine-welded fabric; lattice girders. 1.2 Steels according to this European Standard have a ribbed, indented or smooth surface. 1.3 This European Standard does not apply to: non-weldable reinforcing steel; galvanized reinforcing steel; epoxy-coated reinforcing steel; corrosion resistant reinforcing steel; prestressing steels (see prEN 10138-1 to -4); indented strip; further processing, e.g. cutting or cutting and bending. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10020:2000, Definition and classification of grades of steel EN 10079:1992, Definition of steel products EN ISO 377, Steel and steel products Location and preparation of samples and test pieces for mechanical testing (ISO 377:1997) EN ISO 7500-1, Metallic materials Verification of static uniaxial testing machines Part 1: Tension / compression testing machines Verification and calibration of the force-measuring system (ISO 7500-1:2004) EN ISO 15630-1, Steel for the reinforcement and prestressing of concrete Test methods Part 1: Reinforcing bars, wire rod and wires (ISO 15630-1:2002) EN ISO 15630-2, Steel for the reinforcement and prestressing of concrete Test methods Part 2: Welded fabric (ISO15630-2:2002) NOTE See also C.2 and D.2. EN 10080:2005 (E) 5 3 Terms and definitions For the purposes of this European Standard, the terms and definitions given in EN 10020:2000 and EN 10079:1992 and the following apply. 3.1 reinforcing steel steel product with a circular or practically circular cross-section which is suitable for the reinforcement of concrete 3.2 ribbed reinforcing steel reinforcing steel with at least two rows of transverse ribs, which are uniformly distributed over the entire length 3.3 longitudinal rib uniform continuous protrusion parallel to the axis of the bar, rod or wire 3.4 transverse rib any rib on the surface of the bar, rod or wire other than a longitudinal rib 3.5 rib height, h distance from the highest point of the rib (transverse or longitudinal) to the surface of the core, to be measured normal to the axis of the bar, rod or wire 3.6 rib or indentation spacing, c distance between the centres of two consecutive transverse ribs or two consecutive indentations measured parallel to the axis of the bar, rod or wire 3.7 angle of transverse rib or indentation inclination, ß angle between the axis of the transverse rib or indentation and the longitudinal axis of the bar, rod or wire 3.8 transverse rib flank inclination, angle of the rib flank measured perpendicular to the longitudinal axis of the rib 3.9 relative rib area, fR area of the projection of all ribs on a plane perpendicular to the longitudinal axis of the bar, rod or wire, divided by the rib spacing and the nominal circumference 3.10 indented reinforcing steel reinforcing steel with defined indentations uniformly distributed over the entire length 3.11 indentation depth, t distance between the surface of the wire and the deepest point of the indentation 3.12 indentation width, b width of the indention to be measured parallel to the axis of the bar, rod or wire 3.13 plain reinforcing steel reinforcing steel with a smooth surface EN 10080:2005 (E) 6 3.14 coil single length of reinforcing steel (usually rod or wire) wound in concentric rings 3.15 de-coiled product reinforcing steel manufactured in coils and subsequently straightened for further processing 3.16 nominal cross-sectional area, An cross-sectional area equivalent to the area of a circular plain bar of the same nominal diameter, d (i.e. 4 2 d ) 3.17 welded fabric arrangement of longitudinal and transverse bars, rods or wires of the same or different nominal diameter and length that are arranged substantially at right angles to each other and factory electrical resistance welded together by automatic machines at all points of intersection 3.18 lattice girder two or three-dimensional metallic structure comprising an upper chord, one or more lower chords and continuous or discontinuous diagonals which are welded or mechanically assembled to the chords 3.19 characteristic value value of a material or product property having a prescribed probability of not being attained in a hypothetical unlimited test series NOTE This value generally corresponds to a specific fractile of the assumed statistical distribution of the particular property of the material or product. 3.20 minimum value value below which no test result shall fall 3.21 maximum value value which no test result shall exceed 3.22 batch quantity of bars, rods, wires or decoiled products of one nominal diameter and one cast either in coils or bars or any quantity of welded fabric or lattice girders of one type produced by one manufacturer and presented for examination at any one time 3.23 factory production control permanent internal control of production performed by the manufacturer 3.24 semi-finished product product which requires further processing in order to achieve the standard and special properties specified in this document for reinforcing steels 3.25 standard property property which is contained in this document as part of the factory production control requirements for every test unit EN 10080:2005 (E) 7 3.26 special property property contained in this document which is not determined as part of the factory production control requirements for every test unit 3.27 standard welded fabric welded fabric manufactured according to specified delivery conditions and available from stock 3.28 purpose made welded fabric welded fabric manufactured according to user's specific requirements 3.29 longitudinal wire reinforcing steel in the manufacturing direction of the welded fabric 3.30 transverse wire reinforcing steel perpendicular to the manufacturing direction of the welded fabric 3.31 twin wires two wires of the same technical class and nominal diameter placed adjacent to each other as a pair in welded fabrics 3.32 pitch of welded fabric centre-to-centre distance of wires in a sheet of welded fabric NOTE For twin wire fabric the pitch is measured between the tangents of the adjacent wires. 3.33 overhang of welded fabric, u1, u2, u3, u4 length of longitudinal or transverse wires projecting beyond the centre of the outer crossing wire in a sheet of welded fabric NOTE For twin wire welded fabric the overhang is measured from the tangent line of the adjacent wires. 3.34 length of a welded fabric sheet, L dimension of the longest side of a sheet of welded fabric, irrespective of the manufacturing direction 3.35 width of a welded fabric sheet, B dimension of the shortest side of the sheet of welded fabric, irrespective of the manufacturing direction 3.36 standard lattice girder lattice girder manufactured according to specified delivery conditions and available from stock 3.37 purpose made lattice girder lattice girder manufactured according to user's specific requirements 3.38 lower chord set of longitudinal reinforcing steels placed in the lower part of a lattice girder NOTE The constituent longitudinal reinforcing steels of the lower chord can be interlinked or not. EN 10080:2005 (E) 8 3.39 upper chord longitudinal reinforcement placed in the upper part of a lattice girder, of which the base steel is either a reinforcing steel or a steel strip 3.40 diagonals reinforcing steels linking the upper and lower chord of a lattice girder NOTE They form harmonic curves in the case of continuous diagonals or are independent elements in the case of discontinuous diagonals. 3.41 lattice girder length, L overall length of a lattice girder 3.42 design height of a lattice girder, H1 distance between the lowest point of the lower chord and the highest point of the upper chord 3.43 overall height of a lattice girder, H2 distance between the lowest point and the highest point of a lattice girder 3.44 lattice girder overhang, u1,u2 length of the diagonals beyond either the upper chord (u1) or the lower chord (u2) 3.45 design width of a lattice girder, B1 distance between the outlying points of the lower chords 3.46 overall width of a lattice girder, B2 distance between the outlying points of a lattice girder 3.47 pitch of diagonals, Ps distance between equivalent consecutive junction points of the diagonals with the chords 3.48 angle of inclination of diagonals, angle between the axis of a diagonal and the longitudinal axis of a lattice girder in the plane of the diagonal in the middle of the height of a lattice girder 3.49 technical class type of reinforcing steel defined by its performance characteristics, identified by a unique product number 3.50 reinforcing steel grade steel grade defined by its characteristic yield strength and ductility requirements 4 Symbols Symbols used in this European Standard are listed in Table 1. NOTE For comparison of symbols used in this European Standard with those used in EN 1992-1-1 and EN 1992-1-2 (see Annex E). EN 10080:2005 (E) 9 Table 1 List of symbols Symbol Description Unit An Nominal cross-sectional area mm2 Agt Percentage total elongation at maximum force % b Width of indentation mm c Transverse rib or indentation spacing mm Ceq Carbon equivalent value (CEV) % by mass Cv Specified characteristic value a d Nominal diameter of the reinforcing steel mm e Gap between rib or inde
