SAE-AS-39029-93-2000-R2006.pdf

SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. SHEET 1 OF 5 AS39029/93 THIRD ANGLE PROJECTION AEROSPACE STANDARD AS39029/93 ISSUED 2000-07 CONTACTS, ELECTRICAL CONNECTOR, PIN, CRIMP REMOVABLE, (FOR DOD-C-83527, CONNECTOR) PREPARED BY SAE SUBCOMMITTEE AE-8C1 FEDERAL SUPPLY CLASS 5935 NOTICE THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MIL-C-39029/93A AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-C-39029/93A. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT. UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT. RATIONALE THIS DOCUMENT HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE 5-YEAR REVIEW POLICY. REAFFIRMED 2006-08 Copyright 2006 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org -,-,- CONTACTS, ELECTRICAL CONNECTOR, PIN, CRIMP REMOVABLE, (FOR DOD-C-83527, CONNECTOR) AEROSPACE STANDARD AS39029/93 SHEET 2 OF 5 AS39029/93 THE REQUIREMENTS FOR ACQUIRING THE CONTACTS DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION AND THE LATEST ISSUE OF MIL-C-39029. FIGURE 1. PIN CONTACT. CONTACTS, ELECTRICAL CONNECTOR, PIN, CRIMP REMOVABLE, (FOR DOD-C-83527, CONNECTOR) AEROSPACE STANDARD AS39029/93 SHEET 3 OF 5 AS39029/93 FIGURE 1. PIN CONTACT - CONTINUED. CONTACTS, ELECTRICAL CONNECTOR, PIN, CRIMP REMOVABLE, (FOR DOD-C-83527, CONNECTOR) AEROSPACE STANDARD AS39029/93 SHEET 4 OF 5 AS39029/93 TABLE I. DIMENSIONS. -,-,- CONTACTS, ELECTRICAL CONNECTOR, PIN, CRIMP REMOVABLE, (FOR DOD-C-83527, CONNECTOR) AEROSPACE STANDARD AS39029/93 SHEET 5 OF 5 AS39029/93 TABLE II. DESIGN CHARACTERISTICS. TABLE III. TOOLS. REQUIREMENTS: Dimensions, design characteristics, and configuration: See figure 1 and tables I and II. Tools: See table III. Vibration: Method 2005 of MIL-STD-1344, test condition IV. Shock (specified pulse): Method 2004 of MIL-STD-1344, test condition A. Mating contact: MIL-C-39029/94A. Low signal level contact resistance: The mating depth shall be 0.153 inch. Contact strength: The bending moment of M39029/93-537 shall be 0.23 lb-in. QPL evaluating activity: Defense Electronics Supply Center (DESC-E), Dayton, OH 45444. International interest: NEPR 57. Part number example: M39029/93-597. -,-,-