SAE-AS-4691D-1997-R2007.pdf
SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. SHEET 1 OF 5 AS4691 REV. D THIRD ANGLE PROJECTION AEROSPACE STANDARD AS4691 REV. D ISSUED 1992-07 REVISED 1997-10 REAFFIRMED 2007-11 FITTING ASSEMBLY, TEE, FLARELESS AND SHORT FLARELESS, REDUCER, RETAINED NUT ON RUN CUSTODIAN: SAE G-3/G-3BPROCUREMENT SPECIFICATION: /4/ AS4444 FEDERAL SUPPLY CLASS 4730 FIGURE 1 - TEE ASSEMBLY FIGURE 2 - INSTALLATION, RETAINED NUT AND RETAINING WIRE Copyright 2007 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:11:48 MSTNo reproduction or networking permitted without license from IHS -,-,- FITTING ASSEMBLY, TEE, FLARELESS AND SHORT FLARELESS, REDUCER, RETAINED NUT ON RUN AEROSPACE STANDARD AS4691 SHEET 2 OF 5 AS4691 REV. D REV. D TABLE 1 - DIMENSIONS AND WEIGHTS BASIC NO. AS4691 /10/ /18/ SIZE CODEDH J +.005/-.020 LB/EA MAX ALUM LB/EA MAX CRES LB/EA MAX TI 20.517.1241.375.3951.146.666 24.614.1561.688.5701.651.954 TABLE 2 - WIRE INSERTION DEPTH PORT SIZE (NOMINAL TUBE SIZE)C 04 .250.076 05 .312.076 06 .375.084 08 .500.095 10 .625.114 12 .750.150 161.000.176 201.250.247 241.500.287 TABLE 3 - LEG LENGTH A SIZE OF PORT #2 FOR ALL PORTS THE SAME SIZE USE AS4674. 11.THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. 12.INVENTORIED PARTS CONFORMING TO THE PREVIOUS “LETTER CHANGE” MAY BE USED TO DEPLETION. 13.INTERPRETATION OF DRAWING PER ARP4296. 14.SURFACE TEXTURE: SYMBOLS PER ANSI Y14.36; REQUIREMENTS PER ANSI/ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 µin Ra. 15.BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 16.DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994 17.DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS ±.010, ANGULAR DIMENSIONS ±5°. /18/ Copyright SAE International Provided by IHS under license with SAELicensee=Defense Supply Ctr/5913977001 Not for Resale, 12/04/2007 20:11:48 MSTNo reproduction or networking permitted without license from IHS -,-,-
