BS EN 10079-2007 Definition of Steel Products.pdf
《BS EN 10079-2007 Definition of Steel Products.pdf》由会员分享,可在线阅读,更多相关《BS EN 10079-2007 Definition of Steel Products.pdf(48页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 10079:2007 Definition of steel products The European Standard EN 10079:2007 has the status of a British Standard ICS 01.040.77; 77.140.01 BS EN 10079:2007 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2007 BS
2、I 2007 ISBN 978 0 580 50483 9 National foreword This British Standard was published by BSI. It is the UK implementation of EN 10079:2007. It supersedes BS EN 10079:1993 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee ISE/5, Technical delivery conditio
3、ns, classification and designation of steels. A list of organizations represented on ISE/5 can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a Britis
4、h Standard cannot confer immunity from legal obligations. Amendments issued since publication Amd. No. DateComments W - - - - - 7 - - - $ - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - W W D - - w - - - - EN 10079:2007 (E) 2 Contents Page Foreword3 Introduction.4 1 Scope 5 2 Nor
5、mative references5 3 Terms and definitions .8 Annex A (normative) Steel products and associated standards.29 Annex B (informative) Notes on the former European Coal and Steel Community (ECSC) definitions and Harmonised Commodity Description and Coding System (HS) definitions.33 B.1 European Coal and
6、 Steel Community (ECSC) definitions.33 B.2 Harmonized Commodity Description and Coding System definitions 34 Annex C (informative) Trilingual vocabulary.36 Bibliography44 EN 10079:2007 (E) 3 Foreword This document (EN 10079:2007) has been prepared by Technical Committee ECISS/TC 6 “Definition and cl
7、assification”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2007, and conflicting national standards shall be withdrawn at the latest by Septe
8、mber 2007. This document supersedes EN 10079:1992. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
9、Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 10079:2007 (E) 4 Introduction There are various classification systems existing in Europe but
10、 this European Standard only deals with definitions for steel products manufactured by or used in the steel industry or by its customers. For example, Annex B provides guidance on the definition systems used in the former European Coal and Steel Community (ECSC) Treaty as well as the Statistical off
11、ice of the European Communities and of the Harmonised Commodity Description and Coding System. The entries that are presented in this European Standard have been ordered systematically, and have been grouped by steel products according to: shape and dimensions e.g. flat products, long products, heav
12、y sections; appearance and surface condition e.g. coated flat products, bright products. This European Standard also contains an alphabetical index, which has been included at the end of this document. EN 10079:2007 (E) 5 1 Scope This European Standard defines terms for steel products according to:
13、a) shape and dimensions; and b) appearance and surface condition. NOTE 1 Although the products are generally defined independently of their end uses or manufacturing processes, it has sometimes been necessary to make reference to these criteria. NOTE 2 All dimensions given in this European Standard
14、are nominal. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 39, Loose
15、steel tubes for tube and coupler scaffolds Technical delivery conditions EN 10017, Steel rod for drawing and/or cold rolling Dimensions and tolerances EN 10024, Hot rolled taper flange I sections Tolerances on shape and dimensions EN 10029, Hot rolled steel plates 3 mm thick or above Tolerances on d
16、imensions, shape and mass EN 10034, Structural steel I and H sections Tolerances on shape and dimensions EN 10048, Hot rolled narrow steel strip Tolerances on dimensions and shape EN 10051:1991 + A1:1997, Continuously hot-rolled uncoated plate, sheet and strip of non-alloy and alloy steels - Toleran
17、ces on dimensions and shape (includes amendment A1:1997) EN 10055, Hot rolled steel equal flange tees with radiused root and toes Dimensions and tolerances on shape and dimension EN 10056-1, Structural steel equal and unequal leg angles Part 1: Dimensions EN 10058, Hot rolled flat steel bars for gen
18、eral purposes Dimensions and tolerances on shape and dimensions EN 10059, Hot rolled square steel bars for general purposes Dimensions and tolerances on shape and dimensions EN 10060, Hot rolled round steel bars for general purposes Dimensions and tolerances on shape and dimensions EN 10061, Hot rol
19、led hexagon steel bars for general purposes Dimensions and tolerances on shape and dimensions EN 10067, Hot rolled bulb flats Dimensions and tolerances on shape, dimensions and mass EN 10080, Steel for the reinforcement of concrete Weldable reinforcing steel General EN 10079:2007 (E) 6 EN 10092-1, H
20、ot rolled spring steel flat bars Part 1: Flat bars Dimensions and tolerances on shape and dimensions EN 10092-2, Hot rolled spring steel flat bars Part 2: Ribbed and grooved spring leaves Dimensions and tolerances on shape and dimensions EN 10106, Cold rolled non-oriented electrical steel sheet and
21、strip delivered in the fully processed state EN 10107, Grain-oriented electrical steel sheet and strip delivered in the fully processed state EN 10108, Round steel rod for cold heading and cold extrusion Dimensions and tolerances EN 10131: 2006, Cold rolled uncoated and zinc or zinc-nickel electroly
22、tically coated low carbon and high yield strength steel flat products for cold forming - Tolerances on dimensions and shape prEN 10138-2, Prestressing steels Part 2: Wire prEN 10138-4, Prestressing steels Part 4: Bar EN 10140, Cold rolled narrow steel strip Tolerances on dimensions and shape EN 1014
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 10079-2007 Definition of Steel Products 10079 2007
链接地址:https://www.31doc.com/p-3647007.html