BS-AU-50-1.4.8-1998 ISO-11795-1997.pdf
《BS-AU-50-1.4.8-1998 ISO-11795-1997.pdf》由会员分享,可在线阅读,更多相关《BS-AU-50-1.4.8-1998 ISO-11795-1997.pdf(12页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD AUTOMOBILE SERIES BS AU 50-1.4.8:1998 ISO 11795: 1997 Tyres and wheels Part 1: Tyres Section 4: Agricultural tractor and machine tyres Subsection 4.8 Method of measuring tyre rolling circumference for agricultural tractor drive wheels ICS 65.060.01; 83.160.30 Licensed Copy: London S
2、outh Bank University, London South Bank University, Sat Dec 09 02:11:18 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 50-1.4.8:1998 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes i
3、nto effect on 15 March 1998 BSI 04-1999 ISBN 0 580 29174 X National foreword This British Standard reproduces verbatim ISO 11795:1997 and implements it as the UK national standard. The UK participation in its preparation was entrusted to Technical Committee AUE/4, Wheels and tyres for motor vehicles
4、, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgat
5、e them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the sectio
6、n entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. C
7、ompliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the ISO title page, pages ii to iv, pages 1 and 2, an inside back cover and a back cover. This standard has been
8、 updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No.DateComments Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:11:18 GMT
9、+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 50-1.4.8:1998 BSI 04-1999i Contents Page National forewordInside front cover Forewordiii Text of ISO 117951 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:11:18 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii blank
10、 Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:11:18 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:11:18 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 50-1.4.8:1998 ii
11、BSI 04-1999 Contents Page Forewordiii Introduction1 1Scope1 2Normative references1 3Definition1 4Principle1 5Test conditions1 5.1Tyre installation1 5.2Test tyres1 5.3Tyre load and inflation pressure1 5.4Tyre measurement1 5.5Test course2 5.6Weather conditions2 5.7Test measurement2 5.8Test speed2 6Met
12、hod of test2 6.1Test preparation2 6.2Test procedure2 7Expression of results2 8Test report2 9Other test conditions2 Annex A (informative) BibliographyInside back cover Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:11:18 GMT+00:00 2006, Uncontrolled Copy, (c)
13、 BSI BS AU 50-1.4.8:1998 BSI 04-1999iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member bo
14、dy interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrot
15、echnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a v
16、ote. International Standard ISO 11795 was prepared by Technical Committee ISO/TC 31, Tyres, rims and valves, Subcommittee SC 5, Agricultural tyres and rims. Annex A of this International Standard is for information only. Descriptors: Agricultural machinery, agricultural tractors, drive-wheels, tyres
17、, pneumatic tyres, tests, determination, circumference, dimensional measurements. Licensed Copy: London South Bank University, London South Bank University, Sat Dec 09 02:11:18 GMT+00:00 2006, Uncontrolled Copy, (c) BSI iv blank Licensed Copy: London South Bank University, London South Bank Universi
18、ty, Sat Dec 09 02:11:18 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS AU 50-1.4.8:1998 BSI 04-19991 Introduction Matching front and rear wheels with different tyre sizes on four-wheel drive agricultural tractors requires accurate rolling circumference values. The test method to determine rolling cir
19、cumference outlined below was developed to follow this requirement. The values thus obtained are not intended for use as levels of performance or quality. The test speed has been set at typical working speed when the four-wheel drive will likely be engaged and the most critical match is required. Ge
20、nerally, the four-wheel drive is disengaged at roading speeds. Therefore, the determination of rolling circumference is not related to the tyres maximum speed, e.g. 30 km/h or 40 km/h. Nevertheless, other speeds or conditions may be run provided it is clearly documented in the results. 1 Scope This
21、International Standard specifies the method for measuring rolling circumference for new tyres, under loaded conditions, made for use on agricultural tractors and machines, and applies to agricultural tractor drive wheel tyres in diagonal and radial construction. 2 Normative references The following
22、standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encourage
23、d to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 4251-1:1), Tyres (ply rating marked series) and rims for agricultural tractors and machines Part 1: Tyre d
24、esignation and dimensions, and approved rim contours. ISO 4251-2:2), Tyres (ply rating marked series) and rims for agricultural tractors and machines Part 2: Tyre load ratings. ISO 7867-1:1996, Tyres and rims (metric series) for agricultural tractors and machines Part 1: Tyre designation, dimensions
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-AU-50-1.4.8-1998 ISO-11795-1997 BS AU 50 1.4 1998 ISO 11795 1997
链接地址:https://www.31doc.com/p-3736710.html