BS-EN-13775-1-2003.pdf
《BS-EN-13775-1-2003.pdf》由会员分享,可在线阅读,更多相关《BS-EN-13775-1-2003.pdf(12页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 13775-1:2003 Railway applications Measuring of new and modified freight wagons Part 1: Measuring principles The European Standard EN 13775-1:2003 has the status of a British Standard ICS 45.060.20 ? BS EN 13775-1:2003 This British Standard, was published under the authority of
2、 the Standards Policy and Strategy Committee on 26 June 2003 BSI 26 June 2003 ISBN 0 580 42151 1 National foreword This British Standard is the official English language version of EN 13775-1:2003. The UK participation in its preparation was entrusted by Technical Committee RAE/1, Railway applicatio
3、ns, to Subcommittee RAE/1/-/9, Wagons (tank/freight), which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in th
4、is document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a co
5、ntract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals
6、 for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 9 and a back cover. The BSI copyright date displayed in
7、 this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13775-1 June 2003 ICS 45.060.20 English version Railway applications - Measuring of new and modified freight wagons - Part 1: Mea
8、suring principles Applications ferroviaires - Mesure des wagons lors de leur construction et lors de modifications - Partie 1: Principes de mesure Bahnanwendungen - Vermessung von Gterwagen beim Neubau und bei Umbauten - Teil 1: Megrundstze This European Standard was approved by CEN on 14 February 2
9、003. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained
10、 on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre
11、has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and Uni
12、ted Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2003 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13775-1:20
13、03 E EN 13775-1:2003 (E) 2 Contentspage Foreword .3 Introduction.4 1Scope4 2Normative references4 3Terms and definitions .4 4Requirements.5 4.1General .5 4.2Conditions5 4.3Temperature.5 4.4Measuring principle.5 4.5Measuring equipment .6 4.6Measuring points, dimensional designations 6 5Driving direct
14、ion, vehicle ends and sides.7 5.1General .7 5.2Driving Direction7 5.3Vehicle ends and sides.7 5.4Bogie ends .8 Bibliography9 EN 13775-1:2003 (E) 3 Foreword This document (EN 13775-1:2003) has been prepared by Technical Committee CEN /TC 256 “Railway applications“, the secretariat of which is held by
15、 DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2003, and conflicting national standards shall be withdrawn at the latest by December 2003. This series of European Standards “Railwa
16、y applications - Measuring of new and modified freight wagons” comprises the following parts: EN 13775-1Part 1: Measuring principles EN 13775-2Part 2: Freight wagons with bogies EN 13775-3Part 3: Freight wagons with 2 wheelsets prEN 13775-4Part 4: Bogies with 2 wheelsets prEN 13775-5Part 5: Bogies w
17、ith 3 wheelsets prEN 13775-6Part 6: Tight-coupled freight wagons According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Gree
18、ce, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and the United Kingdom. EN 13775-1:2003 (E) 4 Introduction It is normal practice in all European countries to carry out checks and measurements on the major components of new
19、and modified freight wagons and bogies. In view of the importance of uniform criteria for international transport in all European countries, this European Standard has been prepared. 1 Scope This European Standard specifies requirements for measuring freight wagons and bogies. This ensures that the
20、measuring methods are applied in accordance with uniform criteria. It applies to new and modified freight wagons and bogies. Provisions going beyond the scope of these requirements ought to be agreed upon by the contracting parties involved. The measuring methods relate to the whole or parts of the
21、underframes with or without add-ons if the geometrical structure does not permit anything else. Where appropriate, other measuring methods not specified here are necessary and ought to be specified in each individual case. This applies as appropriate to bogies. 2 Normative references Non Applicable.
22、 3 Terms and definitions For the purposes of this European Standard, the following terms and definitions apply: 3.1 modified freight wagons modifications which change the original identity of the freight wagon NoteIn this case, the sub-assemblies ensuring operational safety ought to be measured in a
23、ccordance with this series in addition to the components changed by the modification. 3.2 modified bogies modifications which change the original identity of the bogie NOTEIn this case, the sub-assemblies ensuring operational safety ought to be measured in accordance with this series in addition to
24、the components changed by the modification. 3.3 finished product product in a finished state in which it leaves the supplier NOTEA product can be a sub-assembly (e.g. underframe bolster), a rough structure (underframe or body) or a finished vehicle. EN 13775-1:2003 (E) 5 3.4 substantial modification
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS EN 13775 2003
链接地址:https://www.31doc.com/p-3737926.html