DD-CEN-TS-15534-2-2007.pdf
《DD-CEN-TS-15534-2-2007.pdf》由会员分享,可在线阅读,更多相关《DD-CEN-TS-15534-2-2007.pdf(12页珍藏版)》请在三一文库上搜索。
1、DRAFT FOR DEVELOPMENT DD CEN/TS 15534-2:2007 Wood-plastics composites (WPC) Part 2: Characterisation of WPC materials ICS 79.060.01 ? Licensed Copy: London South Bank University, London South Bank University, Sun Jun 17 07:16:21 GMT+00:00 2007, Uncontrolled Copy, (c) BSI DD CEN/TS 15534-2:2007 This
2、Draft for Development was published under the authority of the Standards Policy and Strategy Committee on 29 June 2007 BSI 2007 ISBN 978 0 580 50896 7 National foreword This Draft for Development was published by BSI. It is the UK implementation of CEN/TS 15534-2:2007. This publication is not to be
3、regarded as a British Standard. It is being issued in the Draft for Development series of publications and is of a provisional nature. It should be applied on this provisional basis, so that information and experience of its practical application can be obtained. Comments arising from the use of thi
4、s Draft for Development are requested so that UK experience can be reported to the European organization responsible for its conversion to a European standard. A review of this publication will be initiated not later than 3 years after its publication by the European organization so that a decision
5、can be taken on its status. Notification of the start of the review period will be made in an announcement in the appropriate issue of Update Standards. According to the replies received by the end of the review period, the responsible BSI Committee will decide whether to support the conversion into
6、 a European Standard, to extend the life of the Technical Specification or to withdraw it. Comments should be sent to the Secretary of the responsible BSI Technical Committee at British Standards House, 389 Chiswick High Road, London W4 4AL. The UK participation in its preparation was entrusted to T
7、echnical Committee PRI/82, Thermoplastic materials. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Amendment
8、s issued since publication Amd. No. DateComments Licensed Copy: London South Bank University, London South Bank University, Sun Jun 17 07:16:21 GMT+00:00 2007, Uncontrolled Copy, (c) BSI TECHNICAL SPECIFICATION SPCIFICATION TECHNIQUE TECHNISCHE SPEZIFIKATION CEN/TS 15534-2 May 2007 ICS 79.060.01 Eng
9、lish Version Wood-plastics composites (WPC) - Part 2: Characterisation of WPC materials Composites bois-plastiques (WPC) - Partie 2 : Caractrisation des matriaux WPC Holz-Kunststoff-Verbundstoffe (WPC) - Teil 2: Beschreibung von WPC-Werkstoffen This Technical Specification (CEN/TS) was approved by C
10、EN on 29 December 2006 for provisional application. The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard. CEN
11、 members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS) until the final decision about
12、 the possible conversion of the CEN/TS into an EN is reached. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
13、Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CENAll rights of exploitation in any
14、form and by any means reserved worldwide for CEN national Members. Ref. No. CEN/TS 15534-2:2007: E Licensed Copy: London South Bank University, London South Bank University, Sun Jun 17 07:16:21 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 2 Contents Page Foreword3 1 Scope 4 2 Normative references4 3 C
15、haracterisation of WPC materials5 Annex A (informative) Technical data templates .7 CEN/TS 15534-2:2007 Licensed Copy: London South Bank University, London South Bank University, Sun Jun 17 07:16:21 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 3 Foreword This document (CEN/TS 15534-2:2007) has been pr
16、epared by Technical Committee CEN/TC 249 “Plastics”, the secretariat of which is held by NBN. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent
17、rights. CEN/TS 15534 consists of the following parts, under the general title Wood plastics composites (WPC): Part 1: Test methods for characterisation of WPC materials and products Part 2: Characterisation of WPC materials Part 3: Characterisation of WPC products According to the CEN/CENELEC Intern
18、al Regulations, the national standards organizations of the following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg,
19、 Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. CEN/TS 15534-2:2007 Licensed Copy: London South Bank University, London South Bank University, Sun Jun 17 07:16:21 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 4 1 Scope This
20、Technical Specification identifies the required and optional properties of wood-plastics composite (WPC) materials. It is intended to be used as a basis for the specifications of WPC materials. 2 Normative references The following referenced documents are indispensable for the application of this do
21、cument. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 117, Wood preservatives Determination of toxic values against Reticulitermes species (European termites) (laboratory method) EN 3
22、17, Particleboards and fibreboards Determination of swelling in thickness after immersion in water EN 1534, Wood and parquet flooring Determination of resistance to indentation (Brinell) Test method ENV 12038, Durability of wood and wood-based products Wood-based panels Method of test for determinin
23、g the resistance against wood-destroying basidiomycetes CEN/TS 15083-2, Durability of wood and wood-based products Determination of the natural durability of solid wood against wood-destroying fungi, test methods Part 2: Soft rotting micro-fungi prEN 15458, Paints and varnishes Laboratory method for
24、 testing the efficacy of film preservatives in a coating against algae CEN/TS 15534-1:2007, Wood-plastics composites (WPC) Part 1: Test methods for characterisation of WPC materials and products EN ISO 75-1, Plastics Determination of temperature of deflection under load Part 1: General test method (
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DD CEN TS 15534 2007
链接地址:https://www.31doc.com/p-3753590.html