BS-5271-1988 EN-50010-1987.pdf
《BS-5271-1988 EN-50010-1987.pdf》由会员分享,可在线阅读,更多相关《BS-5271-1988 EN-50010-1987.pdf(10页珍藏版)》请在三一文库上搜索。
1、BRITISH STANDARD BS 5271:1988 EN 50010:1987 Specification for Low-voltage switchgear and controlgear for industrial use Inductive proximity switches Methods for measuring the operating distance and operating frequency This European Standard EN 50010 has the status of a British Standard. UDC: 621.316
2、.542.9:621.3.011.3:621.3.027.2:621.317.3.08:621.3.064 Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 12:23:09 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5271:1988 This British Standard, having been prepared under the direction of the Power Electrical Engineering Standards Committee, was p
3、ublished under the authority of the Board of BSI and comes into effect on 29 January 1988 BSI 12-1999 First published July 1976 First revision January 1988 The following BSI references relate to the work on this standard: Committee reference PEL/10 Draft for comment 84/29153 DC ISBN 0 580 16456 X Co
4、operating organizations The European Committee for Electrotechnical Standardization (CENELEC), under whose supervision this European Standard was prepared, comprises the National Committees of the following countries. AustriaLuxemburg BelgiumNetherlands DenmarkNorway FinlandPortugal FranceSpain Germ
5、anySweden GreeceSwitzerland IrelandUnited Kingdom Italy Amendments issued since publication Amd. No.Date of issueComments Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 12:23:09 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5271:1988 BSI 12-1999i Contents Page Cooperating organizationsInside
6、 front cover National forewordii 1Scope3 2Methods for measuring the operating distance3 3Method for measuring the operating frequency f3 Figure 1 Method for measuring the operating distances3 Figure 2 Output signal of the inductive proximity switch for direct current during the measurement of operat
7、ing frequency f4 Figure 3 Method for measuring the operating frequency4 National appendix AInside back cover National appendix BInside back cover Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 12:23:09 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 5271:1988 ii BSI 12-1999 National foreword T
8、his British Standard has been prepared under the direction of the Power Electrical Engineering Standards Committee and is the English language version of EN 50010:1987 “Low-voltage switchgear and controlgear for industrial use. Inductive proximity switches. Methods for measuring the operating distan
9、ce and operating frequency” published by the European Committee for Electrotechnical Standardization (CENELEC). This standard supersedes BS 5271:1976 which is withdrawn. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsi
10、ble for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 4, an inside back cover and a back cover. This
11、 standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 12:23:09 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPE
12、NNE EUROPISCHE NORM EN 50010 October 1987 UDC: 621.316.542.9:621.3.011.3:621.3.027.2:621.317.3.08:621.3.064 Key words: Low-voltage equipment; inductive proximity switches; measuring method; operating frequency; operating distance English version Low voltage switchgear and controlgear for industrial
13、use. Inductive proximity switches. Methods for measuring the operating distance and operating frequency Appareillage industriel basse tension. Dtecteurs de proximit inductifs. Mthodes de mesure de la porte et de la frquence de commutation Industrielle Niederspannung-Schaltgerte. Induktive Nherungs-s
14、chalter. Meverfahren zur Ermittlung des Schaltabstandes und der Schaltfrequenz This European Standard was ratified by CENELEC on 3 December 1985. CENELEC members are bound to comply with the requirements of the CENELEC Internal Regulations which stipulate the conditions for giving this European Stan
15、dard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CENELEC General Secretariat or to any CENELEC member. This European Standard exists in three official versions (Engl
16、ish, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CENELEC General Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of:
17、Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxemburg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr
18、 Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels CENELEC 1987 Copyright reserved to all CENELEC members Ref. No. EN 50010:1987 E Licensed Copy: sheffieldun sheffieldun, na, Mon Dec 04 12:23:09 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 2 blank Licensed Copy: sheffi
19、eldun sheffieldun, na, Mon Dec 04 12:23:09 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 50010:1987 BSI 12-19993 This European standard was prepared by the Technical Committee 17B of CENELEC. 1 Scope This standard applies only to inductive proximity switches. 2 Methods for measuring the operating di
20、stance 2.1 Construction of the target The target is a square made of mild steel, Fe 360, according to Euronorm 271), having a thickness of 1 mm. The length a of the side of the square is equal to: either the diameter of the circle inscribed on the active surface of the sensitive face, or three times
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS-5271-1988 EN-50010-1987 BS 5271 1988 EN 50010 1987
链接地址:https://www.31doc.com/p-3773240.html