ISO-11088-2006.pdf
《ISO-11088-2006.pdf》由会员分享,可在线阅读,更多相关《ISO-11088-2006.pdf(24页珍藏版)》请在三一文库上搜索。
1、 Reference number ISO 11088:2006(E) ISO 2006 INTERNATIONAL STANDARD ISO 11088 Fourth edition 2006-10-01 Assembly, adjustment and inspection of an alpine ski/binding/boot (S-B-B) system Montage, rglage et contrle dun ensemble ski/fixation/chaussure (SFC) pour skis alpins Copyright International Organ
2、ization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/18/2007 21:35:39 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 11088:2006(E) PDF disclaimer This PDF file may contain embedded typeface
3、s. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringin
4、g Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimize
5、d for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2006 All rights reserved. Unless otherwise specified, no par
6、t of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 5
7、6 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2006 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/997254
8、5001 Not for Resale, 04/18/2007 21:35:39 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 11088:2006(E) ISO 2006 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references. 1 3 Terms and definitions. 2 4 Skiers parameters 3 4.1 Ge
9、neral. 3 4.2 Weight method 3 5 Equipment parameters. 3 5.1 Choice of new equipment 3 5.2 Visual inspection and preparation of used equipment. 4 5.3 Assembly. 4 5.4 Binding-to-boot fitting adjustments 4 5.5 Initial indicator adjustment 4 5.6 Functional check (inspection of functions) . 4 5.7 Measurem
10、ent of release moment 5 5.8 Report 5 Annex A (normative) Definition of skier type 6 Annex B (normative) Method of setting. 7 Annex C (normative) Flow chart. 9 Annex D (normative) Clean versus lubricated diagnostic test for boot/binding compatibility 10 Annex E (normative) Drill 11 Annex F (informati
11、ve) Tibial width method 12 Bibliography. 16 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/18/2007 21:35:39 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO
12、 11088:2006(E) iv ISO 2006 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each me
13、mber body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International E
14、lectrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards ad
15、opted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of pa
16、tent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 11088 was prepared by Technical Committee ISO/TC 83, Sports and recreational equipment, Subcommittee SC 3, Ski bindings. This fourth edition cancels and replaces the third edition (ISO 11088:2004), subc
17、lauses 5.1, 5.7 and 5.8, and Annexes A, B, C and F of which have been technically revised. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/18/2007 21:35:39 MDTNo reproduction or networki
18、ng permitted without license from IHS -,-,- ISO 11088:2006(E) ISO 2006 All rights reserved v Introduction International Standards exist for the components of the alpine ski/binding/boot (S-B-B) system, mainly intended for the component manufacturers. An International Standard (ISO 8061) also exists
19、for the selection of release moments. The present International Standard is intended primarily for retailers. However, its aim is to include in one text the different phases of the choice of components, their assembly, adjustment and inspection in the form of practical procedures, and to provide tol
20、erances for inspection and adjustment. The inspection procedures and tolerances described in this International Standard apply to the condition of the S-B-B system before it leaves the ski shop and are not intended to be used to judge the condition of the equipment once it is put into use. Copyright
21、 International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/18/2007 21:35:39 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization
22、 Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/18/2007 21:35:39 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 11088:2006(E) ISO 2006 All rights reserved 1 Assembly, adjustment and inspec
23、tion of an alpine ski/binding/boot (S-B-B) system 1 Scope This International Standard specifies assembly, adjustment and inspection procedures for the binding mechanisms of skis, integrating in a practical way, the requirements of those International Standards which are related to skis, bindings and
24、 boots. It is intended for all individuals and institutions concerned with those procedures, and especially for sports retailers. It is applicable to a ski/binding/boot system (S-B-B) for alpine skiing, of which at least one component is owned by the user. NOTE In the case where the two components (
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 11088 2006
链接地址:https://www.31doc.com/p-3774164.html