ISO-2330-2002.pdf
《ISO-2330-2002.pdf》由会员分享,可在线阅读,更多相关《ISO-2330-2002.pdf(10页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD ISO 2330 Third edition 2002-05-01 Reference number ISO 2330:2002(E) ISO 2002 Fork-lift trucks Fork arms Technical characteristics and testing Chariots lvateurs fourches Bras de fourche Caractristiques techniques et essais ISO 2330:2002(E) ii ISO 2002 All rights reserved PDF di
2、sclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, partie
3、s accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to
4、 the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2002 All
5、 rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country o
6、f the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ISO 2330:2002(E) ISO 2002 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a w
7、orldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented
8、on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafte
9、d in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. A
10、ttention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 2330 was prepared by Technical Committee ISO/TC 110, Industri
11、al trucks, Subcommittee SC 2, Safety of powered industrial trucks. This third edition cancels and replaces the second edition (ISO 2330:1995), of which it constitutes a minor revision. The Scope has been modified. INTERNATIONAL STANDARDISO 2330:2002(E) ISO 2002 All rights reserved 1 Fork-lift trucks
12、 Fork arms Technical characteristics and testing 1Scope This International Standard specifies manufacturing, testing and marking requirements for solid-section fork arms, for quantity production and with all types of mounting. These include, but are not limited to, hook, shaft or pin, bolt-on and ro
13、ller type fork arms. By agreement between the fork arm manufacturer and the purchaser, these requirements may also be applied to fork arms not intended for quantity manufacture. 2Normative references The following normative documents contain provisions which, through reference in this text, constitu
14、te provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent edition
15、s of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 148:1983, Steel Charpy impact test (V-notch) ISO 683-1:1987, Heat-treatabl
16、e steels, alloy steels and free-cutting steels Part 1: Direct-hardening unalloyed and low-alloyed wrought steel in form of different black products ISO 2328:1993, Fork-lift trucks Hook-on type fork arms and fork arm carriages Mounting dimensions ISO 2331:1974, Fork lift trucks Hook-on type fork arms
17、 Vocabulary 3Terms and definitions For the purposes of this International Standard, the terms and definitions given in ISO 2331 and the following apply. 3.1 prototype fork arm fork arm intended for quantity production where any combination of the blade, shank cross-section, material specification, h
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ISO 2330 2002
链接地址:https://www.31doc.com/p-3776662.html