汽车外文翻译半机电性气门在一台单缸火花点火发动机排放影响.doc
《汽车外文翻译半机电性气门在一台单缸火花点火发动机排放影响.doc》由会员分享,可在线阅读,更多相关《汽车外文翻译半机电性气门在一台单缸火花点火发动机排放影响.doc(20页珍藏版)》请在三一文库上搜索。
1、Effect of a semi electro-mechanical engine valve on performanceand emissions in a single cylinder spark ignited engine(Department of Automotive Education, Karabuk University, Karabuk 78050, Turkey)E-mail: ; dogan_oguzhanyahoo.co.ukReceived Feb. 25, 2009; Revision accepted July 7, 2009; Crosschecked
2、Nov. 8, 2009Abstract: In this study, an electro-mechanical valve (EMV) system for the intake valve of a four stroke, single cylinder, overhead valve and spark ignition (SI) engine was designed and constructed. An engine with the EMV system and a standard engine were tested to observe the effects of
3、the EMV on engine performance and emissions at different speeds under full load. The EMV engine showed improved engine power, engine torque and break specific fuel consumption (BSFC). A 66% decrease in CO emissions was also obtained with the EMV system, but hydrocarbons (HC) and NOx emissions increa
4、sed by 12% and 13% respectively. Key words: Semi electro-mechanic, Camless engine, Electro-mechanic engine valve, Engine performance, Emissions doi:10.1631/jzus.A0900119 Document code: A CLC number: TH131.Introduction All internal combustion engines (ICE) have mechanically actuated systems for openi
5、ng intake and exhaust valves. Traditional valve systems have con-stant valve timing which restricts engine performance especially at low and at high engine speeds. Control-ling valve operation in ICEs effective method for improving engine performance and emissions over a range of engine speeds. Para
6、meters such as cam shape, valve timing, valve opening duration and valve lifting have a major impact on engine performance and emissions (Barkan and Dresner, 1989; Krauter et al., 1992; Hatano et al., 1993; Cinar, 1998; Akba, 2000; Pischinger et al., 2000; Stein et al., 1995). To increase torque and
7、 reduce fuel consumption in gasoline engines, manufacturers are increasingly using variable valve timing systems in production engines. Most valve timing systems used for improving engine performance are dependent on the camshaft. The mechanical variable valve timing systems are complex but greatly
8、reduce the limitations of traditional valve systems, especially in regard to volumetric efficiency (Barkan and Dresner, 1989). However, except for BMWs Valvetronic system, they cannot control all parameters such as valve timing, valve lifting and valve opening duration simultane-ously, continuously
9、and completely independently. Lotus Engineering has developed research and production versions of their fully variable valve system that are not dependent on camshafts. The Lotus system can also independently control valve timing, valve lifting and the duration of valve opening. The power and torque
10、 increase obtained by using variable intake valve timing is between 5% and 21% The improvement in fuel consumption obtained by variable intake valve timing is between 6% and 30% (Ahmad and Theobald, 1989; Barkan and Dresner, 1989; Dresner and Barkan, 1989; Asmus, 1991; Demmelbauer et al., 1991; Goul
11、d et al., 1991; Hatano et al., 1993; Urata et al., 1993; Lee et al., 1995; Levin and Schlecter, 1996; Moriya et al., 1996; Pischinger et al., 2000). The improvement in CO emissions obtained using variable intake valve timing is between 5% and 60% (Dresner and Barkan, 1989; Gould et al., 1991; Lee et
12、 al., 1995; Moriya et al., 1996). In some studies, hydrocarbon (HC) emissions were shown to increase with the use of variable valve timing (e.g., Lee et al., 1995). Other studies showed that HC emissions were reduced by between 4% and 40% (Dresner and Barkan, 1989; Gould et al., 1991; Lancefield et
13、al., 1993; Moriya et al., 1996). Nox emissions were reported to decrease by from 30% to 90% (Dresner and Barkan, 1989; Gould et al., 1991; Lee et al., 1995; Moriya et al., 1996). The opening speed of the valve increases the volumetric efficiency of the engine and the reduction in valve lifting decre
14、ases the friction arising in the valves (Levin and Schlecter, 1996). With a variable valve timing system employing the EMV system, all relevant parameters can be controlled simultaneously and completely independently. Therefore, in addition to improvements in fuel economy and emissions, engine perfo
15、rmance is greatly improved (Levin and Schlecter, 1996; Pischinger et al., 2000). The variable valve timing system, which is a completely electro-mechanical system, does not need a camshaft and therefore enables the production of a camless engine. A semi electro-mechanical camless engine is one in wh
16、ich only intake or only exhaust valves are driven electro-mechanically. Camless engine systems have a great potential as they have the advantages of a mechanically working variable valve timing system and because the control of valve performance parameters is easier. There is a considerable collecti
17、on of literature on camless engines. Recent studies have focussed on the control of the solenoids used in the EMV system and computer modeling of such control systems (Stubbs, 2000; Boie, 2001; Wang, 2001; Chang et al., 2002; Tai, 2002; Wang et al., 2002; Hoffmann and Stefanopoulou, 2003; Nitu et al
18、., 2004; Peterson and Stefanopoulou, 2004; Kamis and Yuksel, 2005; Copeet al., 2008). However, a mass production camless engine has not yet been produced.n this study an EMV system was designed based on systems built by other engineers. The EMV engine (a semi electro-mechanical camless engine), whic
19、h enables electro-mechanical operation of the intake valve, and a standard engine were tested to understand the effect of EMVs on engine performance and emissions at different engine speeds under load. During the engine tests engine valve timing, valve opening duration and ignition timing were kept
20、constant to observe the effects of the EMV system alone. 2. Electro-mechanical valve system The components that comprised the electro- mechanic valve actuator (EMVA) were similar to those of other systems (Stubbs, 2000; Boie, 2001; Wang, 2001; Chang et al., 2002; Tai, 2002; Wang et al., 2002; Hoffma
21、nn and Stefanopoulou, 2003; Nitu et al., 2004; Peterson and Stefanopoulou, 2004; Kamis and Yuksel, 2005; Copeet al., 2008). They included an engine valve, two electro-magnets, an actuator spring and a valve spring. The diagram of an EMVA that is commonly used is given in Fig. 1. Principally, the act
22、uator is like an oscillating mass-spring combination and is activated by an electro-magnetic force. The potential energy is transferred between two springs via the core and the valve throughout normal operation. The voltage is applied to the relevant coil during the transition. The magnetic force fo
23、rmed overcomes the spring, friction and gas flow forces. The upper coil closes the valve and the lower coil opens it. The EMV system works in three different positions: voltage is applied to the lower coil to open the valve. The magnetic traction force formed moves the core and opens the valve. When
24、 no voltage is applied to the coils, the core is centered exactly in the middle of two coils and in a neutral position. In this position, the valve spring and the actuator spring are compressed equally and the valve is half open. Voltage is applied to the upper coil to close the valve. The core move
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 汽车 外文 翻译 机电 性气 一台单缸 火花 点火 发动机 排放 影响
链接地址:https://www.31doc.com/p-10026740.html