公制外螺纹6g常用规格极限尺寸表细牙.docx

《公制外螺纹6g常用规格极限尺寸表细牙.docx》由会员分享，可在线阅读，更多相关《公制外螺纹6g常用规格极限尺寸表细牙.docx（2页珍藏版）》请在三一文库上搜索。

1、公称直径义螺距螺纹精度等级大径中径小径螺胚直径最大最小最大最小最大最小最大M3X0.356g2.9812.8962.7542.6872.6022.712.73M4X0.53.9803.8743.6553.5803.4393.603.63M5X0.54.9804.8744.6554.5804.4394.604.63M6X0.755.9785.8385.4915.3915.1665.425.46M8X0.757.9787.8387.4917.3917.1667.427.46M8X17.9747.7947.3247.2126.8917.267.29M10X0.759.9789.8389.4919.3

2、919.1669.429.46M10X19.9749.7949.3249.2128.8919.269.29M10X1.259.9729.7609.1609.0428.6199.089.12M12X111.97411.79411.32411.20610.89111.2511.29M12X1.2511.97211.76011.16011.02810.61911.0811.12M12X1.511.96811.73210.99410.85410.34210.9110.95M14X113.97413.79413.32413.20612.89113.2513.29M14X1.513.96813.73212

3、99412.85412.34412.9112.95M16X115.97415.79415.32415.20614.89115.2515.29M16X1.515.96815.73214.99414.85414.34414.9014.95M18X117.97417.79417.32417.20616.89117.2517.29M18X1.517.96817.73216.99416.85416.33416.9016.95M18X217.96217.68216.66316.50315.79716.5816.62M20X119.97419.79419.32419.20618.89119.2419.29

4、M20X1.519.96819.73218.99418.85418.34418.9018.95M20X219.96219.68218.66318.50317.79718.5718.62M22X121.97421.79421.32421.20620.89121.2421.29M22X1.521.96821.73220.99420.85420.34420.9520.90M22X221.96221.68220.66320.50319.79720.5720.62M24X123.97423.79423.32423.19922.89123.2323.29M24X1.523.96823.73222.99422.84422.34422.8922.95M24X223.96223.68222.66322.49321.79722.5722.62M27X126.97426.79426.32426.19925.89126.2326.29M27X1.526.96826.73225.94425.84425.34425.8925.95M27X226.96226.68225.66325.49324.79725.5625.621.螺胚直径指滚丝前的尺寸，数值为依经验公式计算而得，在实践中需验证。【本文档内容可以自由复制内容或自由编辑修改内容期待你的好评和关注，我们将会做得更好】精选范本，供参考!精选范本,供参考！